What are the options for insulation? I would be interested in an insulated door from schweiss doors. Thanks.
I have a bifold Schweiss hangar door that I would like to insulate. I am interested in your insulated panels if I can use them for an existing installation without too much effort. I can't tell from the website if I have to remove the exterior metal or if I can just install them to the internal metal frame. I was planning to use some 2" foam board but this looks better.
Building a CBS hanger. 40 deep by 60 wide. 17ft walls. Hanger door is planned to be 50 X 14. I would like the exterior to be insulated panels. What type of power is required for the door and do you supply the engineering tech specs for the door and the insulated panels? Ethan
Do you have any insulation kits for your bi fold doors, or is there a way to insulate them? Recently purchased a bi fold door last fall.
I am looking for a quote on a 25' X 14' high insulated bi-fold door and also a 25' wide X 16' high insulated bi-fold door. We are located approx. 1.5 hours north east of Toronto. Do you provide engineering requirements for the openings? Regards, Jack
I would like a quote for an insulated bifold door 211 inches between the door posts of an older pole shed. The header height is 128 inches to the concrete. Also, where is my closest dealer? Thanks very much Samuel
Hi I was wondering what the cost would be on a bifold door that would have a opening of 18x26'? Also can your doors be insulated? Thanks Stanley
Hi, how much per sheet are your insulation panels for bifold doors? Looking at 28 4x8 panels. Thanks
Looking for 20' x 20' bi-fold insulated exterior door for farm/barn application. Would like to apply exterior finish to face of bi-fold door. Looking for rough opening dimensions and does this size of door require motorized opener.
I need a price on a bi- fold door with hole opening 12ft. Wide by 10ft. Tall insulated. Thanks Gary
Need 18' clear open height. Will need an insulated door. Option for 75' wide. Please advise required opening height.
This is actually an interior application in a performing arts center. It will hang on a glue lam beam 7 inches wide by 27 inches high. An insulated door would be best. Please give the weight of the door as well as a cost estimate. Thanks, Grant
Hi, We are looking to replace our 37' w x 23' h door for our storage building with a lift-strap bifold door, please quote for door with insulation and wind rating of at least 90 mph. Thanks, Don
Interested in pricing on insulated bifold door installed. Aprox size is 20ft wide by 13'6" tall. would also like quote on door with walk door.
We will be building a hangar this coming season and am looking for a good quality door that will give the best results in both our colder climate and in longevity, we were thinking an insulated bifold door would be a good choice. would be easier to open during the winter when there is snow in the way.
I'm looking to get a quote on a 12ft wide by 10ft high heavily insulated door that does not minimize interior head room. It will be for a sculpture studio that is being built between April and June of this year. I'm open to suggestions but I am assuming a bifold door that opens up makes the most sense. I'm partly interested in this style of door because of the partial exterior covering that this kind of door provides when open. The plan is for my building to be all wood construction if necessary I am open to adding steel where it is needed for the stress of the door.
I have a customer that has lack of headroom and would like to know what a bifold would run. It is for a snow groomer shed. would like more insulation than a rollup door. opening needed is 11'6" wide by 10'6" tall. anything that you could help me with would be great.
Looking to get a bid on a 40' wide by 16' tall hydraulic door. Please include the price of an insulation and weather sealing kits.
This really fits perfectly but I would like to get an idea of price before proceeding have occasional high winds need cold weather package
Good morning, I have a 16 by 60 foot hydraulic door. I am interested in purchasing a insulation package for it. Could you be please quote me for it. Thank Peter
I am interested in very unique doors for use in Canada. I'm in need of a 22' wide by 18' tall door and two 18' x 18' doors. I have power, but I want a manual control as well. I need very good insulation on the doors, R16 or better. The more insulation the better, it's very cold here.
I just purchased a hangar that I would like to convert to all season. I was browsing the internet and came across your insulated panel system. I was wondering if you sold the panels to the general public. I need the panels to cover a 44' wide x16' tall lift-strap bi-fold door. I would be shipping them to NY. Thanks, Tom
We just purchased an approximately 8-year old hanger that has one of your lift-strap bifold doors and I was curious what our options are for insulation. I have pictures that I can send but this door is not insulated. The hanger right next door has a similar doors of yours with white plastic film covered insulation. Is there a 'kit' that I can purchase from you to get the pre-cut insulation panels? Thanks, Stan
I am looking for your newest panel insulation with white vinyl backing to do a repair to a hanger door at Flying Cloud, MN do you stock this at your Schweiss Door factory? Sure is some slick looking stuff. I heard its selling like hotcakes.
I looking for a hydraulic door 20 foot wide 12 to 14 tall would prefer putting my own siding on it, is this a option? I've read about your new Schweiss interlocking panel door insulation. Can that be shipped with the order to SC so I can install it myself?
Requesting pricing on a strap type bifold door. 24 feet wide by 11 feet tall. No outside skin. RI Owner will apply outside surface siding (if that is possible). Need only total frame assembly and mechanism and Schweiss interlocking insulation panel system.
I would like a quote on 1-14'x14' insulated bi-fold with opener and lift straps, installed in Mt. Pleasent, MI.
Working on a job and was hoping you could provide me with CAD files to figure out our trims and panels on your bifold door. I can't find anything regarding clearance required. We are sheeting the door with 2.5" insulated panels. Thank you, Rick
Need a quote on 46 17 HYdro insulated with windows door. Also quote on same door in bifold style. Will except e mail only
PLEASE USE E-MAIL FOR CORESPONDENCE WE HAVE A STEEL BUILDING AND WOULD LIKE A PRICE ON A 10X10 BIFOLD DOOR INSTALLED. NEEDS BEST INSULATION PKG. YOU HAVE AVAILABLE AND REMOTE OPENERS.
I am interested in a 50 x 14 bi-fold / lift strap door. Priced with windows (8) 3' x 4' and without. We are in Soldotna Alaska and also wonder about insulation options. I have a catalog from the Alaska Airmen's Show, so I don't need anything additional mailed to me. I would very much in fact like to NOT receive any sort of misc. mail from you or any other vendors you might use. We are thinking of building (4) hangers and would make all of them the same size for simplicity. We don't know if we will build steel or wood. I'm looking at both and waiting for some pricing.
Good morning. Im interested in price quotes for weather insulation kit for aircraft bifold hangar door with opening as 10 feet x 40 feet door. Right now it is just metal siding on bottom half and lighter material on the top half. I am also interested in rubber insulation on side posts. Please contact via email. Kind regards, Nikita.
I am looking for a price on a 30 ft Schweiss bifold door for a post frame building. It needs to be insulated or be able to be insulated.
Hi, we are updating trucks and need to get max height out of our building. We currently have a 12' x 16' overhead door and we need to get around 13' so we are wondering about a 13' x 16' Schweiss insulated bi-fold door or if cheaper a Schweiss Doors hydraulic door.
I have just purchased a 16' high x 22' wide roll up door and saw your add and was just wondering what the price of a bi-fold door that size. I would think that a Schweiss Bi-fold Door would be a lot better insulated than the roll up door I have.
Do you make a Schweiss door for lumber dry kilns? We are looking for a door 30' wide and 14' high. It also has to be insulated for high temp. approx 150 deg. We are not going to build a new kiln until spring but are looking to get our plans and material ready this winter.
Have 14' sidewalls on building with valted rafters. Building is 60' x 90'. Need the bifold door to be very well insulated, R-19 or better as it will be on the North end of the shed. Building is currently a cold storage shed, will be sectioning off approx 45' x 60' for a shop.
I am looking for a bifold garage door - 16 ft wide and 9 ft high - residential door - bead board paneled door with windows on the top. Do you Sheet the doors or insulate them?
I need quote ASAP for 16' x 14' High insulated Bi-Fold door for a tractor museum in La Porte County please. Quote new Lift-Straps and if possible before end of 11/28 would be greatly appreciated.
I am working with a customer in the Centralia, IL. area and I need to price a 35' wide x 14' or 15' high bi-fold door. the door would include 1'' thermax insulation board. Thanks
Looking for bi-fold door with straps and i need installation priced. Job is in Mn. and i'll be heating the structure. add weather kit and insulation package.
I am looking at installing a Schweiss bi fold door. I would like to get a price for a 20' wide 14' high door compared to a 25' wide 14' high door. Also I am wondering the wieght of the doors as it will affect the design of my trusses. Further, are the bifold doors insulated, I would like to keep this building heated. Finally, what are the price comparisons between the different styles of doors? Thank you for your help.
My hangar is 40 feet wide with a 39x14 foot opening and I'm looking for a bifold door at a reasonable price. Please quote lift straps and insulation, Call or e-mail for more info.
Is it possible to have a quote. Is the winter kit something you sell ?? Please list the cost of any other options. I will not want walk doors or windows in any of the doors. Let me know if there are exterior finish options other than color. Thanks
We are looking for a price to place foam insulated panels for a Hangar door that is 20' x 4'. If you can assist us, please give me a call at the above number or email. I would like to compare your prices to other quotes. thank you so much, Mark
Interested in a verticle lift bi-fold door. Needs to excellent R-value (note, if you sell me the skeleton, I can build the sheathing myself). Nothing too big, 10ft wide x 8 ft tall. Can be shipped to Eureka, Montana for me to pick up if that makes it easier.
The bifold door we spoke about is 40' wide x 45' high. it will be located in the center of the endwall in a metal building with an eave 48' high. Roof slope will be a 1/2" per 12" and the ridge will be 50' high. Under seperate cover i mailed you next day mail drawings showing the appearence of the building with floor plan. Questions: Can we supply and install our building wall panels to match the building. Do you install the bifold door? Would we install blanket insulation on the inside of the door? How much headroom does your door take up in the open position? I assume this is from the bottom of our header Loading requirements: 110 MPH wind Ss .09- 3.00 S1 .09 and .o66
Please contact me as soon as possible. Have a project going and need price on a 29x16 Schweiss bi-flod with straps. include the option for the insulation and inner liner.
Providing a bifold door proposal for a methyl bromide log fumigation building, with two 34' wide x 12' height doors. The building needs to be well insulated and air tight when closed. Any options?
I have a new garage workshop constructed that has a 16w x 8h opening for a garage door. My desire is to have a high R-Value insulated bifold door with insulated windows across one section. The exterior would be finished in conventional trim to match the home. Can you provide the door frame, mechanism and pricing? Any ideas you might have would be greatly appreciated. Thanks in advance.
Begining design stage of Ag shop 70' X 45' wood frame. Looking at a bifold between 30 - 40 feet wide if you could quote the 30 and 40 that would help. Also the difference in pricing for an insulated vs non insulated.
I have a 40' wide (less the two 6X6 posts)hanger that I would like to install a door on (either bi-fold or hydraulic. What is the putchase cost and installation cost? How much power (current and voltage) is required to operate the door? Thanks
I need a price for 1) 70' wide x 20' high, insulated, bi-fold door installed in Kentucky. Door needs to have everything including windows at or about eye level, at least 6 evenly spaced.
Looking for a quote for a 40' X 14' folding door with lift straps. The building is a wood post frame with corregated tin and is insulated the door need to insulated. Is is in Canada. Also I prefer email contact.
Bifold door: please price installed, please make a note on thickness of insulation, i can install the insulation in the door or if you have insulation option.
I have a contractor that is looking for a bifold lift-strap door price with installation. 24 foot wide opening with 18' sidewalls. figure the schweiss door with remote operator, some windows, insulated door, with installation.
Good Afternoon,could you please provide a budget cost to supply and install a bi-fold door for a new build steel hanger with dimensions 12.500 metres wide from conc.reveal to conc.reveal and 4.500 metres high from finish floor level to under side of conc.down stand beam.The opening height is very important to maintain if possible. To be priced seperatly the door to fully insulated and clad with cedar timber and to have a sperate pedestrian access door. Thank You Regards Charles V.
I am working on a project for Metal Bldgs. Inc. Is it possible to send the design specifications for the 40'x12' bifold door. My client will be adding a lot of weight to the door, thick sheeting, insulation, plus extra's. Just need to get my ducks in a row. Thanks in advance, Rory
Please price the hydraulic doors listed below. At this point we are only quoting this project. Can you let me know what the typical installation cost would be for these (Just a ballpark cost) Thanks.
I a looking for a residential application that will be used in a game room. Probably a bi-fold with nylon straps 8' to 10' door that will open to the back yard. I am concerned about how to insulate the door as we live in Arizona and is quite hot in the summer. Can you send me photos with examples that might work. Pricing would also be good.
Need quote for a schweiss vertical lifting nylon lift strap door. Inside of door must be insulated. Approx R-30 foam with plastic face covering. Include door opening operating equipment and remote control. Job location: New Jersey.
FURTHER TO OUR PREVIOUS REQUEST, WE WOULD LIKE PRICING ON AN INSULATED BIFOLD DOOR AND LIFT STRAPS FOR THE SAME BUILDING AS PREVIOUSLY DESCRIBED. THANKS
We have a hangar with two mechanically operated hydraulic swing out doors. We need some solutions for obtaining remote controls the doors.
Current installation is a conventional industrial roll-up door mounted on the inside of the wall. We are seeking a new hydraulic door design that can be well sealed and heavilly insulated. The construction of the wall is split face cinder block on the vertical sides, smooth cinder block across top. A wall detail is available. The concrete floor is flat up to the edge of the wall, then it slopes down and away from the building.
I have fourteen foot sidewalls not sure if I could do a 14 tall hydraulic door? Would like it to be insulated.
PLEASE PROVIDE A QUOTE AND SHOP DRAWING FOR THE FOLLOWING: (1) 40 X 12 BIFOLD DOOR INSULATED WITH ELECTRIC MOTOR EXTERIOR SIDING TO BE SUPPLIED BY BUILDER include freight to Spokane, Wa 99224
Bifold Door need to be insulated with (1) 3070 walk door unit. The wedge to be 24" for actual door height 16'-0".
I am interested in a free standing bi-fold door. The inside measurement is 13'9" high by 23' 61/2" wide. Please contact me. I would like to discuss insulation packages and prices. Thank you. Sincerely, Kevin
we need a quote complete hydraulic doors kits-1- 24'x 14' 1 pc door and 2-12 x 14 -1 pc doors- we will put 29 gauge steel sheeting with 1.5" insulation under siding- we need shipping to same location as address above. we plan to start warehouse addition by feb 15 doors by march 1-10. Thanks, Tom
I am interested in a hydraulic one piece door for a shop in-the-clear opening of 16 feet high by 30 feet wide. This opening has northern exposure, opens into a heated shop with a concrete floor with about two inches of concrete above the gravel grade that leads into the shop. The building is wooden laminated column and the current 16 H x 15.5 duel sliding doors are clear span supported by a track on the front of the building. I am interested in better sealing of the door opening and the possibilities of insulation that you offer for this type of a door. I am retired and farming a small farm, but I do spend a lot of time in the shop and need better air infiltration control. This is an inquiry only at this point. Further action will depend on the price with and without installation of the door after all of your questions are answered. I am looking forward to corresponding with you. Peter
just starting to plan for a shop, like to now more about the suport need to hold your doors,and also live in a cold and windy climate, how mutch heat loss is to be expected and how to seal bifold door from wind viberation and heat loose.
Is it possible to purchase the 4 inch insulation from you for my Schweiss door? I just installed a heater in my building, so now it's time to insulate. If so - could you quote me a price? Sure like my bifold door, it's quality from the word go. Thank you.
I have 2 14'x14' openings to fill. they did have standard doors that were taken before i got the building. My biggest concern is price and insulation on your hydraulic doors as it gets cold here.
I am looking at Hangar doors which I will build the Hangar around. Bi-Fold doors are interesting, not pretty but cost effective. Living in Alaska, heating is critical, your doors can be insulated but what about the seals when the doors are closed? How much insulation can be placed on the doors? Sprayed urea? Insulation batting? Standing by your guidance here. Thanks, Door opening 100 ft X 25 ft (door must open to allow an aircraft with a 24 ft 6 inch tail height to enter the aircraft hangar.) AOPA / EAA member if that helps pricing, Thanks Terry
Please advise our cost FOB Brantford ON 1 only BiFold Door 70 x 23 Electric Insulation and siding by others Thanks Bill
WE PURCHASED A HANGER-HOME AT THE ADDRESS ABOVE, BUT WANT TO SEAL THE DOOR BETTER. UNDERSTAND THERE IS AN UPGRADE FOR THE BOTTOM DOOR SEAL, AND ALSO FOR THE SIDES (LEFT AND RIGHT) OF BI-FOLD DOOR. PLEASE CAN I GET A PRICE FOR THESE? AND ALSO FOR THE REMOTE CONTROL ENTRY OPTION? THIS ISN'T A SCHWEISS DOOR. THANKS
I am trying to find out what the rubber seal would cost me for the bottom of an old 48 foot bifold door. Thanks for any information.
We have a hangar at Lake Elmo Airport with a hydraulic door that we fabricated ourselves approx 6 years ago and it works fine. We are interested in your new bottom seal. The door is fifty feet wide. We are modifying the bottom of the door and would appreciate your sending us the ideal clearance necessary between the bottom of the door and the concrete floor. The thickness of our door is three inches. Please send us price information for consideration of placing an order. Thank you,
Please provide a price quote on the "Standard Bottom Foam Cushion Kit B1". My door is 43ft wide. Thanks.
Could I get pricing for replacement rubber for my aging bifold door. 12" x 50' qty 2 17" or 18" x 50' qty 2 Thank you Mike
Could you please price the following for me. I have a bifold hanger door. 42' x 12'6" 1. New bottom door seal. The one for inside on one side. 2. 2 top rubber seals. probably need 50' pieces. 3. 4" insulation blanket for the door. Thank you
Please give me a quote on the bottom door seal rubber strip to fit a 48 foot bifold door. Thanks
There was a quote generated by your company last year for a project in Coatesville, PA. The height of the hydraulic door we now want to order is the same how ever the width is only 54'. We would also like a weather seal kit included.
I am looking for a price on the Foam Cushion Seal. Bifold Door size is 70'0'' wide. I would need a shipped price to Alpha Door System. If you need additional information let me know. Thank you, Scott
Door to be insulated with 4" blanket insulation. Will also have metal liner on inside of bifold door.
We need 62 ft. of top rubber seal for bi-fold door. our door serial # is 3812010100001. The doors did not come from your co. But we thought you could help us with this. Also will be contacting you about installing a hydraulic door for us in the near future.
I was looking for a bottom cushion to seal off our door 50' wide Bi Fold Door How much is the Rubber material? Thanks Tom
It would be appreciated to add to your bifold quote. The complete cold package, The single lever latching system, the inside liner panel, single insulated windows (8 in two rows)and the price for each upgrade equipment items. Thank you
In need of a 40' X 12 or 14' bi-fold insulated door. Need a price on the door as well as a price on shipping to Seattle. Thanks
I am interested in a 16 X 16 hydrallic insulated door kit with a walk door priced picked up at your location
Looking to build this summer. Please quote door with and with out insulation. Delivered only and delivered and installed.
I need to get pricing ideas for a customer. He is unsure about which is better (Bi-Fold or Hydraulic) and he is unsure what size he wants. I need budget pricing on the following:36' x 18' 40' x 18'44' x 18'Also would like to have options for straps on the bi-fold door.Not sure yet if the door is in an endwall or sidewall since bay spacing will be determined by door size.Options for insulation on doors? High R-Values are desired.
Please Plan For 4 Windows 4'X3',Controls On Right Inside,Weather Seal Kit,Set Up For Insulation and Liner,
Try this again, if you got my first one I hit wrong button. need quote on following doors 1-24x16 insulated in Rochester, 18'sidewalls 1-20 x16 uninsulated in New Prague option insulated 18' sidewalls
need info on a clad 10'x8' insulated ( all options, top of the line) hydraulic bifold. labor and material numbers for budgeting pourpous, please call ASAP thank you
we want to quote this with our 70 ft door that you already did for us and we want them both insulated. Thank you
door header is steel beam. no man door required. low clearance above header. need insulation. prefer outside of door flush with outside of building. lift straps ok. please quote budget price on installation if possible. thanks and regards.
wanting to price a bi-fold door that would be 180 inches tall by 288 inches wide. would need to be insulated.
We recently installed a 36' bi-fold with straps, autolatches, interior truss version of your door. We have it sheeted outside and are using it. We were wondering if we can insulate the door with spray-on foam inside, and if there is anything you have can tell us about doing this on your door. The building is going to be heated. We are experiencing a LOT of condensation on the inside of the door and are looking for a good way to seal it up tight to avoid this. Thanks. Kile C.
Would you please give me an estimate for a 32 X 15 bifold door delivered to Belfast, Maine. I would want one with the highest insulation value available. Please respond only by email as I will be away from my office for the next few weeks. Thanks.
Please provide a quote for thefollowing information. Please quote FOB Seattle dock.Building will have 3" insulated panels on walls. so 3" panels will be on door as well. Please design accordingly. Panels to be by All Weather.
I'm looking for a quote on a hanger door. I want it to be insulated or at least be able to insulate it. My building is 40'x60'x14' I have 39' inside width and 13'6" inside height opening to work with. Thanks, John
I would like a quote on two doors, insulated with windows. One is a side door 16' wide x 15'8" tall opening. The 2nd is an end door 22' wide x 16' tall opening.
Hi, I need a quote for (3)(insulated) bi-fold doors- door #1 20'6" wide 13'7" tall - door #2 26'6" wide 12'9" tall - door #3 23'6" wide 14'9" tall
i was wandering what do u get for a 12'wide/10'tall insulated door complete ready to install, or send me more of a detailed flyer
I Need A Price On a 50'0" x 24'0" Insulated Bi-Fold Door Complete With Opener. Thank You Bryan B.
I have A Client looking for a 40' Wide x 16' tall bi Fold door will need to be insulated May need you to Install Job will be in MT Sterling OH
Insulation package required with minimum R20 rating. Hanger will be located at Josephburg airport. Minimum of 14 ft clear opening desired. Building side wall will be 16 ft and about 1 ft of grade beam above finished floor.
I've got an industrial building with a roll up door. I am interested in an bifold door that is able to be insulated to replace the roll up. The door opening is 16' wide and 14' high. Can you quote? Thank you, Ben B.
Need Shipment to Maine included in quote Also Need Mandoor in Hangar Door if possible Insulated Door or Door prepared for insulation I also have pictures I can send on EMAIL if required
I was looking for a price for a 22x14 door. it doesn't have to be insulated. But if you have time to price both ways that would be great. Thanks for you time. Mark
Please add (6) 2'0" x 4'0" 1" Tempered Insulated Glass Windows to the Bi-Fold Door. Door to be insulated and lined - please add those components. Thanks for your assistance.
i would like a price on a 20x15 bifold door with insulation. I also need to have specifications for installation in an endwall of a wood frame building. call or email with questions. thanks
Please provide me with a price on an Insulated, Motorized Bi-fold door. I need an 80' x 18' clear opening. Job site is in Gilmer County, Ga. Thank You.
I have an opening for a door that is 8 ft wide and 83.5 inches high. Can you build a insulated door for me and what would the cost be.
I am interested in a bifold door about 14 ft wide and 13 ft high. I would like to have a couple of windows in it. I would also like to have some insulation in it.
already sent on the other form. would like to have a quote for a 40 ft x 18 ft hydraulic door that is insulated. If there is a more economical door size, would like to know that also. Have not yet purchased a building. Priced both steel and wood and have not decided yet. Which building is easier to install your door in?
Need a quote on a 25x16 AND a 25x18 Bi-Fold Insulated Installed By You Steel Installed By You Power Opener Wood Framed Opening
I am looking for a simple bifold door for my wood Kiln. Temps are never more than 180F. Door needs to be insulated and my opening is approximatly 12 wide by 11 high. If you could give me a rough cost for such a door I would apppreciate it. I will be needing two for the Kiln and at least one for my new shop. Right now I just need pricing on two for the kiln that are the dimensions mentioned above. Thanks Kirk A.
I am looking to build a shop next summer, I am interested in high R rating isulated doors and want to compare pricing of bi fold to overhead Thank John
I also submitted a request for a 20x20 door for the same location a moment ago. Doors must be wind coded and insulated. I am looking for the Bi-Fold type door; I don't think I specified that in the other quote request.
Please quote a price for: An insulated bi-fold door. Size to be such that the opening after the door is raised is 18' x 50'. also include the motor and complete lift lower mechanism. Please communicate by email not the telephone.
***135MPH WIND LOAD*** need insulated door if possible last one fell through - sorry - :) this is long-term but looks very promising. please make quote good through jan 31 2008, or advise that time is a factor (advise of timeframe)
Hello; I have a door opening of 50x17. Is there any door that we can use that will allow us the full use of the 17 feet , curently have a bi-fold door that only allows us a little less than 15 feet of openning. It needs to be insulated well enough for New Hampshire winters. Thank you Dennis
Please give me a quote on both types of doors. I need it insulated Does it have to hang from top with the frame or can it mount to side posts? That would make my life a lot easier. How high above door opening does bifold need? Miter cut?
We are looking at beginning construction in November for our hanger and would like a new price quote for a door. 1. 42' X 14' Opening 2. We want to insulate the door and finish the inside 3. Bottom Drive Unit 4. Straps 5. Auto- Latch System 6. Inte al Truss 7. Installation Cost 8. Can this be installed before the concrete is poured? Thanks, Paul
We design and manufacture dryers and kilns, primarily for the ceramic industry. Currently, we have a project to supply a large dryer for a customer that will require two (2) doors, each approximately 16' wide x 8' high. The doors would be exposed to temperatures as high as 400 deg. F on the interior, so they will need to be insulated. We can install the appropriate insulation, as long as the doors are designed to accommodate it. I would prefer bi-fold style doors, but am open to any style. Please give me your comments.
Please send quote on 2 - 16'x16' doors. Also what is the effective R-value (insulation value) of the door. Thanks, Dave
fully insulated doors,endwall (1) 10x10, sidewall(2)8x7 (width x height). Sidewall height is 9 feet, endwall will be 9 feet height - 24 feet from side to side topped with a 9-12 roof design
I want a walk door in the left hand end facing door no glass in walk door or main door, and also an insulation package for door The concrete is ready so I need to get a door ordered asap. Thanks Russ
I need quoting on 2 each 18' x 70' insulated hyraulic doors operated by minimum 40 AMP, 7HP electric motors. Installed price as well Location is to be GEORGIA BULLOCH COUNTY
I'm building an RV garage and would like a quote on a one piece door with the "M" mounting style, internal truss, insulation (R-9?), and a covered/finished inside surface. The exterior will be either steel panel (to mimic a regular garage door) or stucco.
Do you have any insulated doors that easily hang on the outside of an aluminum framed building? Either a bi-fold or roll up door? This building will be going to the North Slope in Alaska. Opening will be approximately 16' x 16'
I am going to build a new hangar and I am getting estimates. The door size is approximate. I would like lift staps and the remote control option, plus decent insulation. We are in a very windy area. This door will have to stand 15 to 20 mph constant winds with gusts up to at least 40mph. Any higher gusting and the door won't be opened. Thank you.
HI I am designing a aircraft hanger to be built this summer.Size is 140 x 50 feet.We plan to build hanger 20 feet high,we have planned two door framed openings of 55x18 feet.These openings can be changed if necessary. Building is planned to be wood framed so that it can be insulated very well.Buiding will be heated with in floor heat.Doors will face south ,door insulation is important to us.I prefer one Piece door but need quotes on both.I look forward to your input.
We have purchased doors in the past from your company. I am now in the need for a door to fill and 15 foot 7 inches clear height x 14 feet clear with. Door motor is the be wired for 460/3/60 and the inside and outside will need to be clad with our matching sheeting and insulated. We will need all the safety controls to meet OSHA or better. The last door we purchased was in 1999 and this door will go next to that door. I would like pricing by Friday or early next week.
I am interested in specifying your door system for stores throughout the country. I would like to find out if it is possible to attach insul. to the outside of your fold up frames so that we can get a high r-value. The doors would be 20'wide x 16" high or preferably 40'wide x 16' high.
Please quote me two doors on will need to be 26'x24' clear height. The other will be 30'x24' clear ht. these doors will be insulated. They will be going into a heated boat storage building that will be a pre engineered building.
talked with a sales man at 2006 natinal frame builders show in nashville and you sent me a info pack but I need a price on 2 doors 1-18'x11' and 1-12'x11' both insulated any questions please call thank terry
we are in the design stage for either 3 or 4 hangars requiring 18' clear height, either 60' or possibly 65'clear width doors we currently have your doors and are pleased we will want insulation, prefer your installation crew; location is to be MRH in North Carolina need net price rom's; do you now need or require 3 phase Bucky
GOODMORNING, I NEED A PRICE ON 1- 80' X 18' SINGLE HYDRAULIC DOOR, THE CUSTOMER HAS ALREADY CONTACTED YOU DIRCECLY FOR PRICING HE WAS NOT AWARE THAT WE HAVE ACCESS TO THESE TYPES OF DOORS, THE JOB IS IN LAPORTE INDIANA. HE HAS STATED TO ME THAT HE WANTS THE DOOR TO BE FOAM FILLED WITH A SPRAY IN POLYURETHANE TYPE INSULATION TO ACHIVE A SANDWICH TYPE DOOR WITH A HIGH R=. DO YOU HAVE A SOURCE FOR THIS TYPE OF APPLICATION? IF SO PLEASE ADVISE.
Need to put in a door for a 24 x 16 opening. Building has 16 foot to bottom of trusses. Need door to be insulated and remote opening. How much height will I loose putting in a bifold door. Need a guesstimated cost for door and installation. Will not be putting door in till mid summer or fall of 07. THANKS Brad
I need to get a quote from you for a 24' wide x 15'5'' tall bifold door. The customer would like to have the door insulated. Also, what do I need for support to hang the door? The building is a steel building.
A friend of mine has one of your doors on his shop. I need a door for a new building that I have just finished. I would like a ballpark price for a door to fit a 15'2" wide x 13'2" high opening. The walls are concrete, 12" thick. I would like to get the "Cold Weather Package" with this door. Thanks, Jon
I would like to get some price quotes and recommendations. I would like to purchase two Bi Fold doors for my steel quonset building. There are two rought openings, one is 19' 9" wide X 14' tal(clearance above door is approx 12" at the co ers). The second one is 11' 9" wide and 12' 4" tall(clearance approx 18" at the co er". I would need the free standing frame. I do want windows in them the number of windows will depend on cost. This is not a commercial building so the doors will not be in constant use. I am interested in the strap type lift (electric). Also interested in insulating, depending on cost. Thanks
I have a Bifold door and would like to winterize it as it does not have any insulation or weather stripping. Need information on what is avaiable and the cost as I want to do it.