I am an engineer working on a manufacturing plant conversion project in Montezuma Iowa. An overhead crane will travel outside the building so we will need a clear opening of approximately 43'-6" wide x 3'-8" high. Building is an existing Star PEMB and this will be installed in a non-expandable gable endwall. Thinking a one-piece hydraulic door will be the best option but would like to discuss the option of using a bifold crane door. I have a preliminary drawing which I can forward to you for reference. Thanks in advance for your help! David C. Loomis, P.E. DCL Consultants,
I need a specialty bifold door quote for a crane door 20'W. Do I need to specify the height or is that a standard number? It's a standard gantry-mounted robot (identical construction to a crane). Not super heavy and won't (obviously) be carrying any additional weight. Point is- it's not a very tall gantry, so a couple feet will probably be enough.
We have a building with crane rails extending to the exterior, leaving an opening above the sliding doors that are under the crane rails. We only have slightly more than 12" vertical clearance between the door opening and the mobile crane. We would like to close this up with a one piece hydraulic or bifold strap lift door. The dimensions of the door would be about 62'9" x 10'-10". We would like to get a quote for this door. Is there a dealer in Arizona, or would we be dealing directly with you? I can supply PDF drawings as well as a 3D step file of the existing building structure to design within.
Would like to know if you work or have installers in the St. Louis area of Southern Illinois? Have a industrial use crane door to install and would like to consider a bifold with straps. Thanks! email or call welcome.
Looking for a bifold crane liftstrap door solution for my shop to maximize height clearance while not interfering with my overhead gantry crane.
Please note the following details: 1)Presently the side jambs are wood but we are capable of fabricating and installing tube steel for a bifold crane door. 2) Existing door is a horizontal sectional. 3) Don't know about outside cladding - could wind up steel or wood (historic designated neighborhood)
We have an 80ft wide by 40 ft tall crane opening we would like to install a hdrauldoor in
Would like a quote on a craneway door that would be 90' wide x 7' tall for bridge crane to drive through on top of crane rail. Below the crane door, we need a hinged door that is 20' wide and 18' tall (top of the crane rail).
We have a total of 4 Bi-Fold crane doors at our facility. We currently have three of them that we can not use. I would like to get a quote on converting them to the strap style crane doors.
I am looking for lifting straps for a bifold crane door operation. The payload capacity would be 1500kgs
I am a General Contractor pricing out a warehouse for a rigging company that deals in oversize equipment. They asked that we provide a 36' x 16' Schweiss Doors bifold crane door. This is going into a new prefabricated steel building we are constructing. Thank you, Joe
Looking at the bifold door custom 20 wide 25 tall crane door: Pricing Shipping Install Warranties Engineering requirements for a wood structure.
We currently have a pleated roll up door on one of our compressor buildings we have no room inside the building for door track due to overhead crane. Looking for a Schweiss crane door that is more weather tight so your bifold door would be just the ticket. The opening is 12' x 12' would like this to be insulated and it is going in a class III location so insulation would have to be non flammable or steel enclosed. Could you offer me a quote for something that would meet our needs. Thanks Steve
Some time when you have a sales rep in the area, I would like to know if you could build and install a bi fold crane door on the end of my existing concrete block building. I may also consider a hydraulic Schweiss crane door depending on price.
Hello, I am working on a precast plant expansion. We are looking at possibly using your bi-fold crane doors as a solution to our problem. We want to be able to run the overhead cranes out the end of the building, but since the plant is near Fargo, ND the weather is causing some concerns. Because of the weather we need to be able to close off the end of the plant at times, but still need to be able to run cranes out. I am looking for some information on your crane door product, the requirements and hopefully some example details. The opening the door needs to cover is 88' wide and 10' tall.
Thinking about putting crane doors on an industrial building I am planning to build. Tell me how your Schweiss crane doors operate and costs compared to other Schweiss door models.
I have a project for a industrial building door, but have to have a rail for a bifolding Schweiss crane door. I want to know if you can take a look at the pictures and make opinion for this.
Schweiss Strap-lift craneway door to be installed in endwall of a new metal building. Need 18' clear. Quote door installation labor and price for a free standing door header and labor to install free standing header. Building will have interior liner door panel. Price fast opening electric door.
Looking for a bi-fold boat house crane door. Crane inside so I can't put overhead. Customer wants a windowed full view aluminum door. Similar to a service station. Will only consider liftstrap boathouse door with autolatches.
I purchased a fairly large metal building (250ft x 120ft, 18' eve, 0.5:12 pitch) and I would like to install a large Gantry crane door in the west end. The roof beam along the end wall is about 12" with 6 vertical columns (including the corners) versus about 16" or 18" beam and 4 columns for the rest of the building. Is it possible to put a bifold door or hydraulic steel crane door in this wall? Desired size of crane door is 50'-60' wide x max ht.
I am contractor needing a quote for a company that needs a 50x16 bifold liftstrap crane door. I prefer a door system with straps rather than cables.
Schweiss Team, you can now begin door fabrication on the previously discussed bifold liftstrap steel crane door for our well drilling company building door in Chicago, Illinois.
I'm ready to order a Schweiss industrial grade crane door. I have your Schweiss Door quote but want to discuss the hyd. vs. bi fold strap systems for this heavy duty crane door application.
Price a bifold crane door to go into an interior industrial warehouse space. Clear opening is 30' wide by 35' high. Need bifold door weight & door clearance required. Will want your liftstrap door.
Our large Gantry Crane door had been causing problems in not being reliable on opening and closing. We'd like to replace it with a Schweiss Crane Door, size is 3900 sq ft and door is either 60 or 65 feet. Can you help with a bifold or hydraulic crane door solution?
We are a contractor looking for a price for your bifold strap crane door to install in our customers new building. I would also like a separate quote for you to hang the door. PLEASE call if you have any questions! Thank you - Chad
I'd like to know what the cost may be for a 12' wide by 14' high bi fold/lift strap or whatever exterior mounted door you may suggest for a building that will need crane doors. Both of your Schweiss doors appear to be ideal for this type application.
I am looking at design options to divide an interior space with a crane door that is 70 feet wide and 45 feet high. There is an existing rigging crane that will occasionally travel back and forth through the area. Is this physically possible with a Schweiss upper bi-fold strap door and two lower hydraulic swing doors? What are the design considerations that we need to be aware of in order to prepare a budget.
I need a revised quote on a Schweiss hydrualic crane door specs are as follows. 50x14 with one walk door located on left side if facing door from outside of concrete block building. thank, you.
Option for insulated panels if you carry them. 3-36"x24" walk door or at least framed openings Able to accept interior liner. This is a crane door, a Schweiss bifold with straps. I looked all over and Schweiss Doors appears to be the only company that specializes in crane doors. One other company said they would try to build me a crane door, but wouldn't guarantee me that it would work to my satisfaction. I can't live with that.
Which door opens and closes the fastest? Do I lose any head room with either door? I only have one truss rafter on the end wall how much bracing will have to be done to support either door? This is for a crane door so it needs to be structurally strong like I'm sure all your Schweiss liftstrap bifold and hydraulic doors are.
I will be building a soon. I need a quote on a crane door about 38 x 10. It does not have to be exactly those dimensions. I can design the opening to fit the door. Please send quotes for both types of doors, bifold with straps and hydraulic with Red Power pump. Thanks, Jake
I think you might have quoted me a crane door last fall but I cannot find it. It will be a 45' by 18' Schweiss one-piece industrial hydraulic steel door. Could you please resend out a quote? thanks, Dan
We have a project where the base bid is to provide a 60x 13.6 hydraulic Red Power crane door. There is also two alternates to increase the width to 65'-0" wide and 70'-0" wide. We would like a quote for price and the design loads to provide the structure with these doors. Thank you
I represent an Engineered Systems team that provides thermal coating facilities to customers globally. We often have a need for indoor acoustical rooms with large custom designere doors to accomodate work pieces to be inserted and removed with overhead cranes. If we could set up a meeting at our NY facility I think our company is ready to purchase some of your doors, we're just not sure at this time whether or not we want Schweiss hydraulic or straplift crane doors. We do want to go with your respected company, because we've seen the workmanship in your product and design.
Do you provide some type of information for what is needed for the free-standing header structure to mount the Schweiss Bifold liftstrap crane door to, or do I have to get an engineer for that.
We are constructing a concrete building in Peterborough Ontario Canada which will need a crane door. Your product is specified. Do you have recommended installers in Ontario? Please let us know who you recommend. Thanks Gary
Looking for an hydraulic crane door 28 x 18. Will be converting a large brick garage which is 34 feet wide and presently has 10 x 10 and a 12 x 13 overhead doors. Need to know how to reframe for the door as well as approximate cost. I will want delivery about June 15th.
Looking for a quote on 20 ft. high and 60 ft metal crane Schweiss door, single piece, Hyd. operated. new construction, BC is providing the metal 80 ft wide by 89 ft deep. Best Regards
Hello! I'm looking for a crane door with a free opening of: 36ft 2inch times 9ft 11inch. 11m times 3 m The walls are made of wood but can easily be reinforced with metal. Please send me some of Your suggested options including price. Fredrik
I have a client that need a 48'x14' high crane door for a railroad engine repair building. Exterior needs to match board & batt siding look. I want a liftstrap bi-fold door just like my Hanger door which you installed last year.. I will supply building plans for details.
DESIGNING A NEW SHOP FOR OUR BUSINESS. BUILDING WILL BE 36' X 42'. WE WOULD LIKE THE SIDE OF THE BUILDING THAT IS PARALLEL TO OUR DOCK AT 42' LONG TO HAVE A SCHWEISS BI-FOLD DOOR WITH LIFTSTRAPS THAT WILL OPEN, ALLOWING US TO SWING A 18' JIB CRANE OUT OVER THE DOCK TO LIFT A BOAT AND THEN PLACE IT INSIDE THE SHOP TO WORK ON. WE WOULD NEED A MAN DOOR ON THE BIFOLD AS WELL. WOULD LIKE PRICING FOR A BIFOLD DOOR FOR THE 42' SIDE OF THE BUILDING DEDUCTING THE MINIMUM COLUMN WIDTH REQUIRED ON EACH END. WE HOPE TO HAVE A 15' CEILING IN THE SHOP FOR THE CRANE CLEARANCES WE WOULD NEED. THANKS
Eastern Vault Comapny is a prestressed and precast concrete producer in West Virginia. We are interested in retrofitting a bifold door to one of our pre-engineered metal buildings. Our newest building, erected in 2007 had one of your Schweiss bifold liftstrap doors installed for our gantry cranes. The door has preformed very well and we are very interested in another unit. The existing door is a sectional overhead door, approximately 20'h x 30' wide. We would like to replace it with a bifold door having a clear opening of 22'h and 40' in width. It would require the external freestanding header.
I have a building that I need to have a gantry crane exit and enter. The Schweiss bifold strap door needs to be 53' wide x 40' tall. Looking for inexpensive solution.
Looking for solution to replace high lift door with a Schweiss liftstrap bi-fold door to minimize impact on overhead crane. Building is designed around standard high lift door frame opening of 14 ft high x 20 ft wide at 100 mph and an R-Value of 13. Metal building girt thickness is 10 inches with a surface mounted insulated 2-1/2" metal wall panel. Looking for a ball park installed cost at Ft Drum, NY. Also, looking for any information on design loads and location on metal building frame.
I need a two fold system. Motorized with safety coordination. A 50' long 7' high crane way door and a 24' wide 30' high sliding door. Can you help?
Need to specify 47' x 27' door opening for an industrial fabrication shop. Would prefer an overhead bifold for speed of operation. The above clearance is required for overhead rolling crane operation thru the opening. We are currently in design for this building and would require two such doors before the end of 2008 installation.
I need a Schweiss bottom drive bifold door - I believe. It is for a 50'-0 x 250'-0 x 30'-0 crane building. Door is going in the endwall. I need a door that requires no bracing between the first two main frames that would prohibit the crane (26'-0 beam height) from being able to reach the first main frame/endwall. I can't tell if the bottom or top drive doors need any.
I need a quote for a 79' wide x 20' tall Schweiss hydraulic door with a sill height 32' above finished floor for crane passage from a metal building endwall. The door will require a remote control, (2) notches for crane beams to pass and an alternate price for Installation (crane rental provided by onsite contractor). The building will be located in Houston, TX (Harris County) using IBC 2003 12/20-110 loads. Also, email and/or mail an installation manual with product brochure and business card. Thanks, Drew
I am planning to build pre engineered steel building 50'x125'x25' eave height. is it possible/ feasable to install a Schweiss liftstrap bifold/ hydraulic door with 5 ton overhead bridge crane in building?
Do you have any Schweiss Door pictures or examples metal building end wall with bridge crane runway that extends thru. Greg
Looking for bids to provide and install a Schweiss craneway door on end of building. Approx. opening is 80 ft wide x 10 ft. high.
We are looking for information on the availability and feasibility of installing a fold-up door on the endwall of an industrial plant that would allow a crane to be removed for installation and servicing. Height approx 40 feet, width approx 110 feet. To be mounted at an elevated location, approx 70 feet above ground. lower portion of bifold liftstrap door would seal at a horizontal wind truss, post framed wall below. Ball Park type budget price would be beneficial to allow client to review feasibility further.