45: HANGAR

1

I am looking for quotes on bifold and hydraulic doors of the following quantities and sizes for use in a hangar project. The heighth dimension given is the clear opening required. 25 qty - 37'W x 16'H 4 qty - 57'W x 20' H 4 qty - 77'W x 20'H 9 qty - 108'W x 28'H

2

Just thinking about building a new hangar with a Schweiss door, wanting to get estimates for total cost before proceeding.

3

WE ARE QUOTING A POLE BARN TO A CUSTOMER THAT'S INTERESTED IN A UPWARD ACTING BIFOLD DOOR FOR ONE END. WE WOULD PROVIDE THE SKIN AND NEED INFO AND PRICING FROM YOUR CO. THE OPENING AT THIS POINT IS 36'W X 12'TALL. THANK YOU, Greg M Spicer mn

4

We are looking at modifying our old ARGG building and making it into a maintainence hangar. To do so we need to replace the current vehicle doors with an aircraft hangar door. The dimensions are approximately 14'H x 40'W. I would like to get a cost estimate for a door. Thanks Mike Hanson

5

Hello, we built a new hangar recently and had a schweiss bi-fold door installed. I was wondering if you had any quality control folks that would be able to come by sometimes in the future and look at our install and give us any input as to the quality of install, maintenance, and upkeep? We are very happy with the quality of your door ..sure glad we went with the Schweiss brand doors

6

I'm looking for a quote on this new Hangar in Menomonie, WI Please see drawing and let me know if you have any questions. I'm thinking a cable lift door but it would be nice to quote a strap door also. I need numbers by Monday or Tuesday of next week.Thank you

7

I would like a price on a 48 ft bifold door for my soon to be built hangar.Thanks

8

We need a price for an 8 panel bi-parting bottom rolling hanger door. The door will be 160'-0" X 28'-0". The door panels on each side of center of door are 3-19'-0" and 1- 23'-0". This project is located in West Palm Beach, FL. The door needs to be designed for winds of 140 mph with an exposure C.We need a price by 11/12

9

we are planning to construct an airplane hangar 82 feet (end wall) by 65 feet and looking for bi-fold doors. pls contact us.

10

I need some contact information so i can forward a package for pricing. Schweiss doors is the specified supplier so i need to get this to you. Thanks Dave

11

I am currently planning a hangar project and will have an opening 49 feet wide by 14 feet tall. Can you give me pricing on a hydraulic door to fit this opening? Can you also tell my the electrical power required to run the hydraulics? How is this door product shipped? I have limited access to my work site and cannot get large trucks to the site. Thank you

12

Not ready to buy. Just getting my ducks together. Considering the cost to buy the lot and build a hanger. I have the price for the hanger less the bi-fold door. So, I'm just looking for a ballpark price for a bifold or hydraulic door. The building will be 75(W)x55(L)x18(sidewall)

13

I purchased a bifold hangar door from you about 3 years ago and I havn't had one problem with it. Now I need another one. It will be 80' wide X 20' high. Please send me some quotes. Thanks, Richard

14

Dear Sir, I need a quote for a Bi-Fold Door,to be instaled in a new hangar, to be designed, including side bars, motors etc. No instalation. Width 72 feet Height 16 feet Whatsh the difference with the Side Wall Door and End Wall Door ??, Price ?? or instalation or better finshing? Please respond by email, Kind regards, Lonny

15

good afternoon, i need a price on a flush mount hydraulic door for an airplane hangar. this is a replacement of a bifold door and measures 54 feet 6 inches wide by 19 feet tall.

16

I have one of your doors on my hanger at Friedens Pa. I can phone you with the model and ser no. if you need. Its about 40w x 14h, gearmotor with cables. I need to install a 50w x at least 16h so I can rent lease to bigger planes. We build experimentals, and need to get bigger. I,m the owner so please call and discuss this with only me via phone. Or u can e mail me. I need to price this in the next two weeks. Dave Schwartz

17

I plan to build a hangar this summer. I want a 50 foot wide door that will clear 15 feet verticaly. I assume that a Bifold door would require 18 foot eves, but with a hydrolic door I might get by with 16 feet. Could you recomend the best and cheapested setup. Also could you include structural engenering requirements for the building so I can compare costs for wood or steel buildings. The building will be 60 X 60 and the door will be on the end wall, centered or on one side, what ever is easiest. Thank you Reagan

18

Please provide a quote for both door systems. This door is for a hangar. Please provide a list of what the unit comes with. Thank you,

19

Please provide a quote on a Schweiss Bi-Fold Door and a Hydraulic Door We are required to submit a bid for End User Customer as follows: Price (3) Bi-Fold Doors for 42 X 14 Framed Opening Price (4) Bi-Fold Doors for 42 X 14 Framed Opening Price (1) 54 X 16 Hydraulic Doors for New Construction Hangar Should you need further information please call our office.

20

Hello: I am a project manager with West Virginia University, and we are preparing to replace the existing bottom rolling doors on hangar that we own. The existing opening is 116'. I would like a quote on two 50'x20' bi-fold doors (one with a 3' man door). Please contact me via email if any further information is required to obtain a budgetary cost.

21

To Julie, Please requote bid number 11508-RM Fax: or phone 4 We are still interested in purchasing a hangar door in early 2010. Thanks Harry

22

We are interested starting a hanger design. Please send info. Thanks. Tom

23

Hangar door for Cessna 172

24

We need bi-fold doors for straight hangars of 50ft width x 50ft depth with height of 18ft door. Can you please quote for this me

25

Please price a 48 ft bifold door for my upcoming hangar home. It will be located in Gladewater, Texas. Please, If you need to call, use my cell number. Thanks

26

I am working on Hangar Project in Alpine Wyoming, I would like as much information about your doors as I can get.

27

I'm going to build a hangar and need to figure out what size to go with. Please e-mail a price on the following: 50x16 clear bi-fold & Hydraulic 42x12 clear bi-fold & Hydraulic 42x14 clear bi-fold & Hydraulic 60x16 clear bi-fold & Hydraulic

28

Hello: I am building a personal hangar at Dayton Wright Brothers Airport (MGY). I am undecided as to purchasing the door direct and having you install it, or having the building contractor do the work. Meanwhile I need to decide what Bi-fold I want. I know the smallest size is 45'x14'. Please provide a price for 45', 46', 48' and 50' x 14 doors so I can decide (No man-door or windows). I would like prices for options of: Auto Latch; Straps; Remote Operator; Installation. Thank you.

29

i would like a quote for a bi-parting door with cable not straps.

30

We currently have bi-fold hangar doors and are looking to replace the insulation. What we have is 60" wide and has a heavy vinyl backing(interior). Any help would be appreciated. Thanks,

31

I started a 42' x 40' hanger building today and need a 40 x 12 bi-fold door

32

Please provide pricing for the following bi-fold hangar doors going to Panama City, FL. There is a base price and several alternates consisting of the same door "groups". The base consists of four groups and all the alternates a single group. Please price each "group" of doors separately including freight and I will apply them to the different alternates. The base quote consists of GROUP #1, #2, AND GROUP #3 X 2 for a total four groups (34 doors). GROUP #4 will be a separate alternate and as stated above all other alternates will be a single group. GROUP #1= Six (6) 59'-6" wide (clear) x 18' tall (clear) GROUP #2= Eight (8) 47'-6" wide (clear) x 14' tall (clear) GROUP #3= Ten (10) 41'-6" wide (clear) x 12' tall (clear) GROUP #4= Four (4) 49'-6" wide (clear) x 14' tall (clear) Doors are to be designed per Florida Building Code with wind speed of 130 M.P.H. Exposure "C". All buildings will have doors in sidewalls. Please provide overall door dimensions for each size Thanks, Gary

33

Please provide a quotation to furnish FOB Lodi, CA. the hangar building or just the door systems for the proposed facility. Comply with all San Joaquin County, California building department requirements. 70' x 100' x 45' clear under the frames 2 ea. 25' x 45' clear opening doors centered in the endwalls 4 ea. 3' x 7' man door framed openings – doors and hardware by others 3" scrim faced blanket insulation in the roof and walls Standard rib siding / SSR roofing - both KXL finish The owner will consider standard rolling hangar doors but would prefer a door system without a track across the opening. Thanks, Dave

34

In design phase of hangar for helicopter and motorhome.

35

I am interested in a price for a 40'x 12' bifold door for an aircraft restoration hangar in Whitefield, NH. Also, is an insulated door available and if so what is the R value? Thanks, James B

36

I have a hangar for my airplane and require a door. The opening is 13'4 high (from the concrete to the beam), and 48'8.5" wide inside measurements. I'm looking for a quote on a door this size. Your early attention to this would be much appreciated. Henry

37

We are interested in a bifold walk door for a hangar. The width of the hangar is 63 feet and height on 20 feet. please supply quote for same to be shipped to Miami fl.

38

I need to get a quote for a 60'w x 20' tall hi-fold door for a aviation building, w/ metal exterior. I am assuming we put the mtl. siding on the door? Also do you have some one who has installed these "Correctly" in our area?

39

Please quote for 40 x 12 bifold door. Please call with any questions. Construction is starting on my aircraft hanger next week.

40

Thank you for the quick response to my request for a quote on my hangar door. Questions? 1. I want to make sure, is your quote in U.S. dollars or Canadian Dollars? 2. Is there any additional duty that I would have to pay at the border? 3. Can I pick the product up at Fairfax rather than having you ship it to my address. 4. Is there any siding or insulation included with the price. Thank you Jim

41

Please contact me about hangar door pricing.

42

Hello, I am considering buying and building the following hangar and I need to know if your door will fit in it. The manufacturer of the hangar said some bi-fold doors fit and some don't. How much of a header is needed for your door. I have seen your doors at the Alaskan Airmans trade show and I like them. Mike

43

I need a quote on a 48 x 14 bi fold hangar door delivered to Chesapeake, VA 23323.

44

Looking for information on Schweiss aircraft hangars for general aviation aircraft. 50 x 50, 60 x 60, and 60 by 80. Our plan is to build 38 of various sizes in 3 to 5 unit buildings. 60 x 80s are planed for business uses and will have additions for office space. Please have Schweiss Call!

45

I would like quotes on a 40x10 and 40x12 hanger door (endwall). I live in Mandan, ND. Thank you Keith L.

46

We need to get a estimate on new Hangar doors, they are 75 long feet by 21 feet tall.. Can you send us a quote. Thank You Sarah

47

Am interested in receiving a quote on: 48 x 14 bifold hangar door 46 x 14 bifold hangar door Thank you.

48

Purchased a door about 7yrs ago and very happy. Thinking about moving and building a new Hanger, will need a door.

49

Are you familiar with this project being bid in Manitowish Waters with four hangar doors? If not I can send plans and specs.

50

We have an existing bifold door on our hangar, but it has an old winch system instead of the hoist system your current doors have. Could you quote the cost for upgrading our old bifold door to your hoist system.

51

Please provide an approximate cost for a bifold door spanning 61' x 16' for a hangar located in NM. Thank you, Barton L. Tate

52

Dear Sir, Madam, Please make a quotation for Bi-fold hangar doors only frame and electrical mechanism. 10 items 3,5m x 11m cleared doorway, 2 items 3,5m x 12m and 1 item 4m x 17m. Metal cowering will be on the place with corrugated steel sheet 0,7mm. Include please shipping costs and term for production. Thanks and best regars

53

Design build project requires hangar door 65' wide x 18' high clear opening

54

Looking at building several hangers and would like to understand your system, schedule & pricing

55

Can you please provide engineering data and door weights for the following. This is a hanger building 90x125 going to LA. The framed opening size will be 80x17.

56

I am planning to build a 50 by 54 hangar in Wisconsin and am intending to put in a 44 by 14 ft hangar door. I am interested in options and prices. Thanks Greg T.

57

Hi There, After a price for a bi fold door that folds upwards for a hangar. Can you supply: 1)Drawings for the door system 2)Approx Manufacture & delivery time Do you supply a manual on the installation of the door for our installers? Cheers Look forward to hearing from you Nic

58

Howdy! Looking at building a hanger-need bi-fold approx. 45 wide with 14/15 slab to bottom on door opening! Would be building this summer in ak. Would like pricing for door, also do they come in 46/48 dimensions for width. Thanks Dorin D.

59

We are just completing the construction of seventeen hangars all with Schweiss Bifold doors. The contractor didn't order the doors with weather seals on the sides or in the middle. Could you please give me price and availability for the seals required to seal the sides and the middle of the door? Approximate door dimensions are 42%u2019 wide by 15%u20194%u201D high.

60

I am building a hanger 50 X 40 in Elbert county Ga (call.)

61

Can an aperational bi fold door be manufactured for a hangar opening to allow a Airbus A320-200 through?Dims: 12m height by 47m minimum opening.Please advise asap, for upcoming U.A.E. hangar client presentation meeting.

62

I am bidding the NC hanger project and need a price on a bifold hanger door. 80' wide with 20' clear height and exterior panels with vinyl faced rigid insulation inside.

63

would like price for a 44 foot wide bifold door for hangar. 10 feet tall is plenty high. If savings for lower height please let me know; could get by with less.Thanks--email only, no calls.

64

I would like to get some pricing as well as more detailed information. Thank You Bo. I have a 60' x 16' hanger that i would like to get priced.

65

I am looking for pricing on a hangar door 32' to 40' wide, 10' high.

66

I need to get a price for bi-fold door for a hangar project in Concord, NC. Could you please tell me who the local rep is for this market?

67

I am working a new hangar project for the University of Michigan. We are looking at a 70'-0" wide clear opening by 16' to 20' clear height opening. Bi-fold fast strap system preferred. Truss can be external if needed.

68

Building new hangar, 45 x45 with 16' eves. Wood pole/truss const. Door 42 wide by 15 high. In design stage. Need quote delivered to Salem.

69

I am putting a 42x48 hangar up in May. Could I get a price installed for a 42x12 bifold door. Roger W.

70

This is an initial quote only, so dimensions are approximate. I am looking into building a hangar and would like to get an idea on the cost of the door.

71

hi we are in the process of building a hanger, we would like to use your type of door system, the door width is 35'6 and the height is 9' could you supply me the cost of the motor. the drive. hinges and fold runners, also i beleive my collegue contacted you and that you are able to supply us a copy of blueprints for the system.kind regards Roger E.

72

Dear Sirs, we are building a hangar and are loking for a door which wouldn't reduce the headroom available. The hangar is a bricked up steel construction with wooden roof truss. The eyelet: with 19.1 m (62 ft 8 inches) height 5 m (16 ft 5 inches) All electrical device should be designed for the European standard which is 400V/50Hz! I am looking forward to your offer. Best regards Pavel S.

73

I HAVE A CUSTOMER WHO WANTS TO BUILD 2 HANGERS 1 IS 50'WX75'L I NEED TO KNOW THE WEIGHT OF THIS DOOR TO GET TRUSSES MADE CORRECTLY TO SUPPORT THE WEIGHT OF DOOR THE OTHER HANGER IS 75'WX75'L THESE ARE BUILDING WIDTHS. HOW MUCH OF AN OPENING CAN I GET WITH THESE DIMESIONS? I LOOKING FOR THE LARGEST OPENING POSSIBLE. THANKS, MITCH

74

Working on planes for a hanger. Door will need to be 52' wide and 14' tall.

75

I have two very old hangars (1930's vintage) that I need to decide whether or not to replace the doors. I need to know my options and the cost of replacement and installation. The size of the openings are approximately 60ft X Do you have a dealer in the Massachusetts area? Someone who can look at the project? Look forward to hearing from you. Thanks, Fred G.

76

hangers not built yet - I am exploring the possibility of building hangers to rent out to other pilots.

77

Need a hangar for a Beechcraft Queen Air.

78

Am building a hangar and interested in prices of doors.

79

Request pricing for a 52x16 bifold for our new hangar going up in April in Milaca Minnesota. We're trying to costs at a minimum.

80

The hangar is newly completed in Altus AR. I hope to install a door sometime in late April or early May. I will be leaving Illinois for FL this coming Saturday and be gone for about two months however my mail will be forwarded and I hope to check my phone calls daily.

81

my new hanger has 55ft door w/ cables and auto locks. the contractor jor c. screwerd up the instalition and didnt give me the manuel. i need instruction manual to adjust the door to try and get it to upen.

82

Need a "RECOMMENDED" hanger building company to build an aviation hanger with one of your doors ? Please email recommendation .

83

NEED BI FOLD DOOR FOR 80X80X22 HANGAR --DOOR IN ENDWALL, CUST REQUESTS60 X 18 CLEAR DOOR WHEN OPEN PLS QUOTE AND LET ME KNOW WHAT CLEARANCE YOU NEED FOR BUILDING FRAME. SITE IS DODGE CENTER MN 55927 THANKS 1/16/09

84

I am building a hanger 40' by 48' with a wall height of 14' I am interested in a quote on your bifold door.I need the door at least 13 by 38.Thanks Cathy

85

Our company is looking at bidding a job to replace fourteen 42' x 14' Bi-Fol doors on hangars in Galveston TX and I wanted to find out the cost. I can send a copy of the specifications to clearify the door requirements. Thanks, Matthew E.

86

I need a quote for 1-60' wide x 19' high bi-fold hangar door and motor operation, with freight. We would also like some literature/binder on your door products and a credit application to become a dealer/distributor. Thank You, Ernest W. J. III

87

I have some drawings i would like to send you for the project we are building. It is a hangar "Condo Complex" so there are numerous doors. Let me know which doors would be correct for these applications.

88

Hello: I need a hangar hydraulic door, frame and equipment, the size is 36 ft wide and 12 ft high, what do you suggest, could you also send me the spec. and price. Thankyou Margo

89

I would like to install a door on my otherwise enclosed hangar at the least possible cost.

90

Hello Gentleman, Am considering installing your bi-fold doors on my hangar. Will need five 50x17' doors. Need an approximate cost figure. Thanks, Peter D.

91

I am purchasing a Hangar at the Rapid City airport that has one of your doors on it. I am trying to evaluate the value of the hangar. Could I get a price on what the door is worth. It is 15' x 50'. It has straps on it. Thanks.

92

Interested in talking to a representative concerning a proposed hangar door to be installed on an existing hangar located in Kinston NC. Please furnish a local contact name and number. Thank you

93

Looking at building a hangar, probably Ram from Winsted, and need a general quote. Jeff

94

Looking at building a 48x48 hanger next spring, need quote on bi-fold door. 40-46 wide not sure? Thanks Larry K.

95

Just looking into hanger building feasibility for me. Thanks

96

Looking for information/pricing on doors for new hanger building (6). need 16x16 clear after wedge

97

I was wondering if you would quote me a hangar door for a project that we are bidding. The project bids Thursday November 20.

98

hanger door

99

we will be needing approximatley 20 hanger doors over a period of 18 months, the houses we are building have openings 14 metres wide by 4.5 metres high, if you are interested in submitting a quote for the project please contact myself on the above details. Regards Damian

100

Can you please give me a price quote for a hangar door for an opening 47' wide by 13' high.

101

I already have a bifold hanger door and would like to install your standard side latches. I would like prices and ordering information please. thank you.

102

Please quote two bi fold doors, 18' x 66'. These will be for two new hangars (one door on each hangar)

103

Hi - I'm looking for a estimate on: - 1 or 2 hanger doors (still TBD, just wondering if there is a pricing difference ordering two) - 60' wide - 21' clearance Please let me know if you have additional questions.

104

I need to get a handle on the cost of a pair of bi- fold doors for a pair of hangers. Each door needs to be 180'X 27'-6", and seven 115'X25'-6",( these will most likely be bi-fold as well)all installed at the zip code above. Jim M. Sr Projects Mgr

105

We are in the process of building a hangar. We require a door 44'long and 12' high. We require an openner and remotes. Please provide a cost for the door shipped to us, the required openner, and the estimated time to install.

106

We require a foldable hanger door of size 90 m wide x 14 m height with necessary supporting system.

107

Hello, I would want to know if you can sell us portail or mobile hangar for a Boeing 737-200 aircraft

108

Hi, Please let me know if you guys will be able to throw me a budgetary number for a bi-fold hangar door that will be installed in Greenwood, IN. It will be great if you can breakout installation.

109

Hi, I'm looking for a door for a hanger building. The Hanger building is 150'wide X 150' deep X 30' tall. Can you please email me the styles that you have and the prices. waiting to hear from you. kind regards, Liza P. Executive Assistant

110

I have a customer that is in need of a 20 x 80 bi fold on a hanger I am bidding. PLease give me an idea of what a door like this might cost.. Thanks Stu

111

Replacing existing rolling doors in 60' x 100' hangar. will need doors in both ends. This is a city funded project and they will be requesting bids from the companies we get information from. We are in the research phase of this and would appriciate any additional info you may have regarding application and installation along with any cost estimates.

112

I am in the process of buying a new hangar in Colo that is under construction. It will have your 58'X16' opening size bi-fold door installed and I wanted to see what you might have available in windows for that type of door. Is there single or double pane windows as an option? What sizes do you have? Let me know at your convenience. Thanks in advance. Ted L.

113

previous purchase of 40x14 hangar door looking for a quote on a door for a clear opening of 34'x10' with max height of 15' to work with

114

Preparing plans for new hanger. Looking at housing minimum of 2 Kingair aircraft (type 90 to 200).

115

We are looking to build a hangar 100' x 120' for up to 4 citations with room to grow into something larger.

116

Like Pricing for a 50'x 20' door for a new hanger

117

Constructing a 3 unit clear span rental hangar for single engine and light twin GA aircraft.

118

We would like a quote on (1) 45 x 16 and (1) 50 x 16 for our project "Z. F. H." in Selah, WA. We are planning on a 16' framed opening. Building drawings are available if it would be helpful. Thanks, Richard

119

Re: Lopresti Hangar Sebastian, Fla Size of opening is 58 feet wide by 18 feet high

120

We are bidding hangers in Moore County NC. Please contact me so I can help you access bid documents.

121

We are quoting 2 Hangars in Lampasas, TX. I need a price delivered (and possibly installed) for 1 door 18' High X 64' Wide and 1 door 18' High X 60' wide. There is also an alternate for an additional Hangar with an 18' High x 60' Wide door. These will be mounted in the end wall with a top drive motor. Have you heard of this project? I also need Loading for these. Wind speed is 90 MPH. Bid date is 7/30. Can you get me a quote by tomorrow noon? Thanks, Sincerely, Mark T. D. Project Manager

122

New construction hangar. Hangar opening is 40' wide X 12' high

123

Have you developed a bifold door that allows a small 8'X 7' garage type door (for vehicle traffic) within the larger bi-fold door? We are in the permit process for building phase one (70 hangars) and more often than not we are not able to place the garage doors on the side or rear of the hangars. Please let me know. Thanks. Rick A. Managing Partenr

124

I am preparing a proposal for a hangar building in the Memphis Area. The building will have (4) 60x16 BI-FOLD doors. The project timing is 2009. Could you give me a budget price for each door with an escalation percentage for material price increase. Also, I would like to know the vertical clearance dims. Thanks, Bill H.

125

Hello, My father is building a 70 ft hangar and would like to equip it with a bi-fold door. What size would you recommend for a hangar that size? And what would be the associated costs of the door? Thanks for your assistance. -C

126

I am quoting a hanager and would like to speak with someone. The opening will be 14 or 16 x 54 Thanks

127

I am sending this request for my father who does not own a computer. Do not call him! He is going to build a 40x50 hangar in Southern Michigan and is looking into the different door options. I believe he is planning on a 40 foot door with 10 or 12 feet of verticle clearance. Can you please send him a catalog and a few rough estimates on your different styles of doors. Thank you, John P.

128

Building a hanger at this time. Local truss manufacture said to get the hinge location information for the prebuild of the trusses. 40' outside to outside of wall, 2"X6"X10'. Location is Fairbanks Alaska, cold weather, bifold door, thinking electric motor / cable or strap. Could I get an approxamate cost of door also.

129

my hangar is going to be 50x50x20ft. how big can i make the bi-fold door to where there will be enough clearance at the top of the biulding. can i get the door at 17 or 18ft high?

130

I like the doors. What about the Hangars? I need a Hangar for size of B1900 and Dash 8-100/300. Any idea's or contacts for Hangars? Best Regards, Gilbert

131

Building hanger for helicopter. 50 x 50 Interested in door that would give 36 feet wide and 18 feet high clearance. Thank you.

132

I am looking for a price for a 20'-0 (tall) x 40'-0 (wide) folding hangar door with installation.

133

Good Afternoon i am writing in regards of a price on your product that was listed in our specs for: Project New Hanger Facility in slidell, la.

134

I am interested on a price quote for a 40' Bi-fold metal hanger door.

135

Could you please provide us with pricing for a 60 by 18 ft. door for our new hangar ? also info on a European dealer is welcome.DFO Allan H.

136

I am looking to price out the replacement of bi-fold hangar doors on an existing hangar. The doors are approx. 16' high by 40' wide. If I know what the replacement cost is (approx.) I can tell the owner what the approx. cost will be (for budgeting purposes). Any information would be most helpful. Fax, email or phone will work. Thanks, Joe F.

137

My hangar will be 100' wide with a 22' eve height. Will this accommodate a 90'x20' hydraulic door?

138

We are in need of an 80' wide by 20' tall (clear opening) bifold for a Hangar in Bend Oregon. Does Schweiss have a high lift option that would reduce my eave height for a door this wide? I have not installed a Schweiss door for a number of years so am looking forward to the opportunity. Could you provide pricing for the door, including freight, and lead time. Thank you, Duane

139

I am going to build a hanger and shop on my new airstrip in the country. I have been talking to various steel frame builders and am not sure if I should go with pole type or ladder frame type construction. From a purely strength consideration for either a bi-fold or one piece hydralic, which would be the best for your doors? I know your doors work with both types but am told that the pole building is overall stronger than ladder frame but I am not sure. Thanks, Russ

140

Please provide price on two(2) 100x28(clear)hangar doors in Portland Maine Please provide required opening height and deflection requirements

141

Hello, I'd like a quote on a 55 x 14 bifold hangar door. there is a 90 mph wind load, and it would be delivered to Palenstine, IL 62451. Thanks, Andy

142

I've got a Schweiss door on my hangar and am looking for the manuals on-line. Are these manuals available in electronic copy (computer files)? Safety Information and Operations Manual - 300 Safety Decals Placement Guide Manual - 310 Bottom Drive Jackshaft - Strap Installation Instructions Manual - 325 Photo Eyes / Safety Edge Installation Instructions Manual - 415 Remote / Receiver Installation Instruction Manual - 875 Photo Eyes / Safety Edge Installation Instruction Manual - 880 Top Override Safety Switch Installation Instruction Manual - 885 Auto Side Latch Installation Instruction Manual - 903 Auto Wind Pin Installation Instruction Manual - 930 Thank you. - Mike L.

143

Pricing for 60' x 20' bi-fold hangar door, delivered to Fillmore, Utah. Price required on or before 5/27/08. Can e-mail drawings/specs if required.

144

Private Hangar installation.

145

Need a 55' W X 12' H bifold hanger door delivered to Lago Vista, TX 78645. PRICE SENSITIVE (low cost). Please quote.

146

We're planning the construction of an hanger for delivery for next November. We'll need a 50 ft wide door. The clearence inside will be 18 ft under the beam. The roof on the door hanger side will be around 26 ft. Would it be possible to install a bi-fold door in this conditions, if yes what kind of budget are we looking at? Regards Eric B. Logistic Specialist

147

We are building a new hangar 70x70x18

148

Please price a 30' wide x 14' high bi fold hanger door. Shipping to Bloomsburg, Pa. 17815. Do you install also?

149

We need quotes for seven doors. We are building 6ea 60X60 hangars and a larger 125 X 60. The 60X60 should be 59' wide with 20' clear height. The 125 X 60 should also have 20' clear height but could be as small as 100' width.

150

Have a 60X60 hanger with a 20x45 wide opening just curious how much it would cost to replace with one of your doors? Thanks Tim

151

In the design stage of a hanger and would like to know price of door 14' high approx. x 45' wide either Bi-fold or hyd.

152

I have a port a port hangar with a one piece tilt up center door and clam shell side doors. Do you have door that would replace just my one piece door? If so, price and shipping charges to CA please. Door dimensions are close but approximate.

153

I need a quotation on one (1) hangar door with a clear opening of 19' x 56'. The customer I am working for says that your company has recently supplied this door for Sane Construction on a project in Tullahoma, TN, and Heartland Construction on a project in Lebanon, TN. It's my understanding that I am quoted the same structure as these two companies have already completed, so that may be of some help.

154

We are building an (8) unit hangar complex and will need 8 doors. All bifold doors will be 50' -0" wide with the heights different due to terrain (3) at 16'-6", (1) at 16'-10", (1) at 17'-2", (2) at 17'-6", and (1) at 17'-10". All doors will have lift straps, 30" wedge, 240 1ph, bottom drive, int. truss, 12" inch top rubber, weather seal kits, and auto latches. Please include shipping to Juneau in your bid. Please also quote all safety options that could work on these doors. Also please quote optional insulation package. Individual owners may choose some of these options. Also please quote on a separate form the cost of having you company install doors. We understand there will be travel expenses. We expect to need the doors installed near the end of June. We need to know the lead time to order these doors so they will arrive on time.

155

WE ARE BUILDING A HANGER IN SPRINDALE ARKANSAS. WE NEED A 60' X 20' DOOR. WHAT IS YOUR PRICE AND HOW LONG WOULD IT TAKE FOR IT TO GET HERE?

156

Please send me a quote on a 60' wide and 20' high bifold hanagr door.

157

looking for a bifold door for a hangar 42'x14', would like a price quote.thanks for any info...

158

I am building a hangar and need the voice of experience to advise on details: ie the benefits of 12 foot vs 14 foot tall door (over time), this will be new construction, does the difference of metal building or wood building have any impact on the door?, and how do the door options affect cost: ie strap vs cable, bottom or top drive, etc. Thanks, Steve

159

Could you price out a hanger door for a 40ft wide by what ever size heigth that will give us a clear opening of 14ft 6 inches

160

I have a 40 X 60 foot hanger enclosed on the 40' sides (14' eves I think) and would like to put a door on the 60' side. Can probably go down to 50' but this would require more construction. I also would like to enclose the rear 60' (no door). I am loacated in Westwego, LA (about 10 minutes southwest of New Orleans. What would be the best solution for me? Please let me know if you can help. If bifold, would like door. Need minimum 12 vertical opening.

161

I am pricing out three different size hangers and would like quotes for the following framed openings; 44' X 14' 44' X 12.5 42' X 14' all doors white, no insulation needed, must be able to seal well. And all with electric opener, no need for extras as I am trying to keep the cost down. Please Email as soon as possible.

162

would like information package on bi-fold door and one piece hyddraulic door. I'm planning on a 11'x 44' hanger door for my hanger. would like to know labor cost to install.

163

I am planning to build a three-bay hanger that has 50'x14' doors. What is the cost difference between the two? The building will be approximately 156'x40' with the three doors along the long wall. Thanks, Blake

164

Price and del. 42 ft X 12Ft bi fold hanger door for Bermuda Dunes Ca

165

I would like pricing a specs on a bifold hangar door with a clear opening of 29'H x52'W

166

Please provide pricing for two (2) motorized 50' x 14' hanger doors.

167

We are in the market for two 60 foot bi fold doors. I need pricing, design information for frame opening and anyother information that may be useful as we design this hangar for our customer. Bret

168

please send a quote for 5 bifold hangar doors installed at kfnl size 12x40 thanks

169

I'm building a hanger in North Idaho and wish to price the hanger door. My opening will be 11'X44'. We will need your modle of Bi fold that can form the smallest wedge at the top position. Art G.

170

We are building a single row of 5 - 50 X 50 hangars with a common pertition wall seperating the individual hangars.

171

I am interested in information on your hangar doors.

172

Need a price on 2ea. 30x24 Hanger Doors

173

Door will be installed on new hanger yet to be built in Arkansas

174

Hi I'm looking for a hangerdoor and it will have to open into the building, it can not be on the outside of wall. Is that possible. Arnar H

175

I would like a cost est. for a 40x12 hanger door, including installations.

176

I'm looking at a project in Northern Minnesota, and need a price on (2) 50'-0" x 16'-0" bi-fold hangar doors. Thank you,Jerry

177

I'm pricing a hangar door 40 to 45 feet in width, 12 feet high.

178

I'm planning to build another hangar. I have bottom cable drive and am very satisfied with it. I need a price for a 45' bi-fold, bottom cable drive. The sidewall height will be 14'. I would also like the price of installation at New Richmond, Wisconsin? Just starting to get bids on 60 x 54 building, so I have no clear openings as of yet.

179

My neighbor Mike S. recommeded your firm and product. I am building a new hanger and need a door that is 46 wide by 14 feet tall. Please get a quote to me ASAP. Also need the specs to give my building company to make sure they build the opening correctly.

180

I need a price and information on a 50'x 14' bifold door for a small hangar.

181

I just bought a hangar with your door. The opening is roughly 13'. I have no idea how high I can open the door. I do know how to adjust the stops on the screw jack mechanism. But just how high can I go with the door? I have a motor home I'd like to store in there along with the plane. Needs to open about 12' 3". Can you advise? Dave

182

Hi, We would like ti receive a quotation for: 4 hangars doors to be fixed on a concrete frame

183

Please price a 40' wide door for a hangar with bottom of trusses at 12' I will be needing it in Dec 2007 Thanks Parker B. Troy, OH

184

I need a quote for a bifold hangar door and height clearances for a 40' x 18' door

185

I would like a budget estimate on a 50' wide bi-fold door. The door will be in the end wall of a 20' eave height hangar. I am assuming a clear opening of /- 16'. Thank You for your quick response. Steve S.

186

can you price out some of your hanger doors? I am sorry I can't give you a specific size. At this moment I am not sure. If you could give me the most common, please.

187

Please contact me regarding a 60' x 16' door. Hangar openin is 75' x 16'

188

For a 40' x 10' single hangar bifold, what is the approximate overhang moment when open and motor power req'd? In this application, ohm's law is the enemy and starting current is the concern. Can the door easily accomdate additional speed reduction to use a lower power motor, albeit at a lower lifting speed? e-mail reply best.

189

May I have a price quote for my 40 foot by 10 foot hangar door

190

I just purchased a hangar with one of your bifold doors with lift straps and bottom power configuration. The door is about 60 feet wide by 12 feet high. It has manual door latches on each side. The door is insulated as is the entire hangar. I am interested to know what a door like that would cost to purchase and install at todays prices? Also, do you have any maintenance guidelines for the motor or other moving parts? Thanks, Steve

191

need quote hangar opening 240 height 30 one or two would be ok...

192

Would like to replace a hangar door on an existing building. I wanted to get prices to give to the contractor.

193

Need Pricing on your Hanger Doors

194

I am getting ready to construct a 60X60 hanger and am looking for a quote for a door. I would like pricing for a 50X14 door. This needs to have an open clearance of 14 feet. Also, please give me the general dimensions needed to fit this door (framed opening). I would also like a quote for the same door in a 55 foot width. This would be shipped to Idaho Falls, Idaho Thank you Craig D. J.

195

Need a quote on 16 ea Bi-Fold Hangar Doors. 40'W x 12'H clr. with 3'0" x 6'8" man door. Thank you, Robert J.

196

I am in preliminary phase of building a multi unit hangar complex. up to 21 doors depending on building schedule... door opening will be 65 X 18 clear. I may mix sizes of Hangars with 50' doors depending on local interest. would like quote on most reliable and cost effective, and CUSTOMER Proof door you have.

197

I'm looking for a bi-fold hanger door 100' x 26'

198

Hello Iam looking for the most economical hangar door for a 40 foot opening 12 feet tall hangar. please contact me asap thanks Darryl

199

Do you have a rep in the state of Oklahoma? Would like some pricing on doors for a 50x50 hangar.

200

I'm looking for a 40 x 12 hangar door

201

My hanger is to be 46'x60'. The door is 38'w x 11'h on the 46' end wall. i.e. I have 4' of wall on each side of the door. Immediately above the door is a 3' rectangular bearing truss which will be the wedge area. In addition to price/shipping charges I need the forces/reactions at points on this end wall in order to complete design of trusses.

202

This is going to be for a helocopter hanger.I hope I gave you everything you need if not please feel free to calll me.The door will need to installed in Rock Hill S.C.

203

I would like to know what the best door options for a hangar opeing that is roughly 42 feet long by 16 feet high. Please get back to me as soon as you can.

204

I will be constructing a drive-thru loadout hanger for an aerial application business and need a quote on 2 bi-fold doors. Opening size is 70' x 16' with a minimum of 14' opening clearance needed. Sidewall height of the hanger will be 18' and opening height for the doors could be made taller if necessary. I would like to have straps instead of cables. Construction will begin in 3-4 months. Please let me know if you need additional information. Tim T.

205

We are quotng a small private hanger for a customer in Reserve, Louisiana and are looking for the price of a bifold hanger door 40'x14'.

206

40' X 14' Hanger door needed Please

207

Interested in a 44 ft by 14ft bi-fold door. Please send price quote. Send quote for complete hanger also if you do that. The door will go on existing hanger with open front. We also have land next door which is able to handle 60 ft wide hanger. Thanks Ken

208

I am building a 60X60 hangar with a 14 foot sidewall. Which door would you recommend and what would be the costs? thanks, Jim

209

Hi, I am looking for a bifold door 10'x 36' for my hanger. can you send me prices. thanks

210

Looking for a quote on a hangar door. Looking at building multiple hangars here at the Craig Moffat A/P.

211

We are designing around a new hangar building addition that will include 2 hangar doors. One door is to be 65' by 17' tall and the other is to be 65' by 16' tall. The owner requests the bi-fold type door. I am working around some height limitations due to existing conditions. I mainly want general information and some assurance that the size of the bifold doors can be done. I also could use some idea of details and clearances needed to accommodate the doors.

212

Interested in replacng accordion door on 66 ft by 24 ft high opening, both ends of existing hangar.

213

Please quote whatever your standard bifold hanger door is about 40 ft long. Thanks

214

We are building a hanger in two months and will require a door. The current estimated size is 40' wide and 10 - 12' high. Bi-Fold, please. If there is a standard door that is slightly out of the given dimensions, let me know. Can you provide me with an estimate?

215

Our schedule for hangar build is around Sept of this year. We will be building a 48' x 56' pole barn construction hangar. Do you have a .pdf install guide available for a free standing door attaching to a wood building? We need information to determine door placement and stresses we may encounter with a 44' bi-fold door with 12' of free clearance. Thanks, Doug

216

Looking for a quote on a 60' x 16' (clear opening) bifold hanger door.

217

I need a door for my hanger that I am in process of building 42 ft opening need price on the best door for the price please call my cell phone as soon as possible

218

We are needing pricing for an 80'-0 wide x 18'-0 high operated door for a private hanger. Please call me so that we can go through the particulars. Thank you, Bryan C.

219

I AM INTERESTED IN YOUR DOORS, HOW DO YOU SECURE THE THE DOORS IN THE FLOOR / WE WILL BE BUILDING A HANGAR IN FL. SOON.

220

Hello, I will be building a 46" wide hanger in about 3 months and i will need a Hanger door Please send me a price list Thank You Paul

221

Looking for a 40' wide by 18' high door for a metal hangar building.

222

Dear Schweiss, We are building a new hangar and looking for a 40ft bi-fold door. What is your Sun-N-Fun special? We are ready to place an order and looking for the best deal we can find. Best regards, Scott G.

223

Dear Sir, Kindly provide the price and delivery time for the followings: Aircraft hanger doors= W x h= 30m x 8m= 3 Nos. 16m x 4m= 1 No. Thanks and regards, Kamal S.

224

Looking for hanger door for new building. Opening is 50 ft.

225

I am building a hanger in Breckenridge. I also need to know how big to build the opening on the building. I am not sure what you mean by end wall or side wall. I want the door in the middle of the wall. The hanger will be 60 by 60.

226

MY door opening is 40 X 12. I have an additional 5" clearance at the top of the door. I also want a small standard 36" X 72" door in my hanger door. I planr to cover the door with aluminum or Hardie Board.

227

I am in the process of gathering information to have a hangar built. I would like a door opening of 40 or 42 ft with a height of 10 ft. What would be the cost of such a door? Thank you, Len S.

228

Seeking a quote for the proposed Worthington,MN Hangar project.

229

I'll be building a hangar in the near future, and would like a quote for a 38' wide, by 14' tall bi-fold door. Thanks, Ron E.

230

Please quote for 40x12 bifold door, including lead time and delivery to Dayton, Texas Please call with any questions. Construction is starting on hanger next week. Thanks, Doug D.

231

To whom it may concern I have received a request for 3 hangars (rather big) and I am just enquiring whether you build big hangars. Tank you and best regards Costantino D.

232

Plan on a 60x60 hangar with a 44' bifold door. Construction to start in May. Thanks, KPS

233

What would it cost for an 11x45 bifold hangar door? Also, how difficult is it to install it?

234

The hangar currently has an opening 39.5 feet wide by 8.5 feet high in the middle and sloping right to left. The opening also has gussets at the top corner each end. Does the opening need to be squared up?

235

I have an existing hanger pipe construction that i need to install 4 bi fold doors on. It already has doors on one end but is open on the other (which they want to enclose) The height of the existing doors is 13' 5" and the opening between the unright pipe columns is 42'4". Also they want a walk door installed in the bottom panel. Please advise if you have a system that will accommodate these measurements. Thanks Roger S.

236

I'm looking for a bifold door for my hanger. I will need 40'wide x 12' high clear.

237

Building a hanger soon, interested in knowing more about your doors.

238

Just begining sizing of building 40x40 hangar is thought to be sufficient.

239

We have a 20 acre project in Chandler Arizona in which we plan on building hangars on fee simple land. Please have a rep contact me. Thanks, Tim.

240

I will be building a 48'X48'X14' hangar in Willow, Alaska this summer. I am interested in the price of a bifold door to go in the end of the building. I would like a horizontal clear opening of at least 40' and as much vertical clear as practical. How much would this door cost? How much would shipping cost?

241

I am a home builder. I have never built a hangar or a steel building. Hangar may be framed of wood or steel. Hangar will be 60x60. Approximately 45'x14' door.

242

I'm looking for pricing on a Hanger door 12' x 40'

243

I am planning to build a couple hangers in the Fairbanks area this year. I would like the price of your 40'x12' door delivered to Fairbanks. Thanks, Ken T. q.

244

We're looking at putting in a couple of bi-folds to replace some sliding doors on a hanger. the inside dimensions of the openings are 40'1" X 11'10". they have a steel beam for the header. Can you get me a price on 2 doors for these openings? Thanks, Tom S.

245

The hanger I am building is 50' X 50'. Can you send me more detailed description of how the end wall must be constructed to have the maximum available width and a 13' clear opening height?

246

Hangar will be 65 x 65.

247

Going to build a 45'w x 54'd hanger,16' eaves,4on12 roof. 14'H x 40'W horizontal bi fold door. would like to price the whole package and also just the door.Please contact me, thankyou Ken G.

248

Will be building three 60x60 hangars

249

To Sales, I need to get a quote and a drawing on a door for a hanger door. Openeing is 38' x 10' with 2' of headroom. Please include an option for motor operation. Any questions, please contact me. Thanks, Joe L.

250

Looking for a local contractor to furnish and install a set of automatic hanger doors. Need to have clear opening of 30 x 14 Insulated doors.

251

We just got a lease on a lot at the Patterson, La airport. We are getting bids on a hanger but most of the contractors want to exclude the door. So looking for a quote on a 50 ft wide bi-fold door for a 60 x 60 hanger. Door opening will be 12 ft.

252

I am planning to build a hanger within the next few montha. I would like information on hanger doors. Thanks, Harry B.

253

I need pricing on a 45 by 12 hanger door for my hanger project in Crawford CO, thank you. Jim

254

Hello, I have an older hanger at the Anoka County Airport. It is 40' wide, and I would guess the rough opening might be 12' high. Currently it has an older bifold door. The mechanics aren't in the greatest shape, and before putting money into it, I thought I'd see if I can get an approximate cost to have it replaced with a new door. I am interested in the least cost, installed solution, that would be insulated with an entry door. Could you give me an approximate range of costs? Thanks! Ron

255

60 X 15 Bi-fold door for hangar or less expensive alternative

256

We are building a hangar for aircraft maintenance purposes and would like to get a general idea of price. We will have a 70 foot opening 20 feet high. (hangar 85 by 65.)what consideration must be taken into account for the door header? What would cost of a bifold be for this opening and also for a hydraulic one piece door. We are in a windy location with winds regular to 10 to 15 mph and can sometimes gust to 25.. will this be a factor with either door. We are in the early stages of planning this hangar and will also be building a 120 by 85 hangar as phase 2. how difficult is the installation, we have our own construction crew available. What would we be looking at for delivery time to penticton BC Canada and what would cost of delivery be? Please also copy any e-mails to Jim.Thanks

257

im building a hangar will have a door opening 40 ft wide 128 inches high,would like to get a price on this size door,will be building in jan 07 awaitng you reply , colour of steel siding on door do we have a choice of colours? or can we put our own on,

258

We are one of three design/build contractors that have been chosen to offer proposals for phase one of a four phase project. Phase Two will go before Phase One is out of planning and of course the carrot is whoever get phase one, will get all other phases. We shall see. Anyway, Phase one is for fourteen 40' x 40' hangers. It would appear from the information I have that most small aircraft that would fit within the 40' x 40' do not exceed a 10' clear tail height. If that is the case, I need a quote on 14 each 10' clear when open doors, that will fit within a 40' opening. What I need right away is what the net clearance will be for that 40' door and what height do I need to make my building to accommodate the door? I need the information on the required building height so that I can get a quote on the buildings. So, if you can get the information back as soon as possible on the building requirements, I can wait until next week, Friday, the 15th for the door quote. Each door will need to have a walk door in the lower portion of the door. I am leaving this morning and will return on Monday, but if I get the information, I will be carrying both my cell and my laptop, so I can get the building quote working as well. Thanks for the help. M. Building Corporation G.W. Michael M. President

259

I'm planing on building a hanger at D95, 40'x50' with a 12' opening.

260

New hanger just applying for building permit. Clear height of opening to bottom of the roof trusses is 16 feet. Width of opening is 44 feet. Total outside width of building is 48 feet. Need detail for contractor to build out the opening. I only want 14 feet of height with door open and could get by with as little as 12 feet. Can it attach it to the bottom horizontal member of the roof truss? I have another hanger done this way with four trusses bolted together (for strength) to form the end roof structure of the building. We can talk via phone after I get some details.

261

Please send me your latest product catalog of hangar doors. Thanks!

262

I am working with one of my builders on a hanger going into Erie, PA. Builder will be Willow Construction. Please provide estimate, via e-mail, for the door indicated below as soon as possible. Top of door will be at 20'-0. Clear open height to be 20' - wedge. If you have any questions please call Doug

263

I need a rough quote for some budget numbers for a door to go into a hangar with a 60'x18' wall, as big a door as I can get.

264

We are currently looking an existing hanger that has two 16' x 80' framed openings. Existing doors where (4) structual framed doors on floor mounted track. Looking for furnished and installed pricing. open for suggustions.PS. 130 MPH Wind Zone Thanks Rick S.

265

Hi, I have two of your doors and am anticipating building another hangar next spring. I'm wondering if you anticipate and pricing changes the first of the year? Thanks, Dan L.

266

Have seen your doors installed on a large hangar in Auckland and need something similar.

267

Dear Sirs, We have one of your doors installed on our hangar, and I'm in need of another remote opener. There was some information on the back of the one we have. You installed this door on our hangar at the Greenwood airport. If you can send me another one, that would be great. Thanks Phil

268

I have a cllent who is a doctor interested in buildling a hangar. A few years back I had worked with another client who never completed his desire to build one, but I remembered your name. Please, if you can mail me a catalogue so that we can determine size and specs during our drafting phase of this project. Thank you Dan W.

269

Do you do estimates and work in Washington State? I have a hanger in East Wenatchee, WA that currently has two roll up doors, but was framed for a full width door during construction. Please advise. Thank you for your time, Leslie

270

Read about your free DVD and would like one sent to me. Also what is your lead time for ordering. Looking at construction in Jan or Feb 07. Actual size of Aircraft hanger has yet to be determined. Planning size is a 60X60 for now. Thanks Larry C.

271

Looking for a hanger door for a 40 foot wide opening by 12 foot tall.Thanks Josh F.

272

I need a guote on a 40'x12' hanger door. I don't realy care which style, price is a big concern.

273

I have a hangar that has a bifold door (homebuilt) that has never been opened or used. I need to see about putting a opener on it.

274

My building is a aifcraft hanger (30'X 40') Wood pole and truss type construction with steel siding and roof. Building is new construction just completed.

275

Need info on bi-fold door for A/C Hanger. Door will be approx 80'x20' ??? A/C is a King Air B200A Our Customer would like something automatic/remote operated. Located in East Texas

276

Building a hangar. Need info regarding bifold doors

277

We are currently designing a project for a local Civil Air Patrol. They have spoken to us about the installation of a bifold door on the hanger of their new building. the door size is to be 44 ft. width by 14 ft. height. they would like a steel door and may possibly like to have an entrance door installed into the bifold door. i would like some additional information on your door and lift systems not only for the client but also for our office as well. thank you. James H