22: STEEL BUILDINGS

1

I have a customer in TX that is interested in your doors. He either wants a bi-fold door with straps, or he wants a hydraulic powered door. The door dimentions are 45 wide by 16 tall. How much support do I need on a steel frame building, and how much clearance do we need above the door?

2

have 12" i beams header and side columns. would like to install hinges to existing i beam.

3

I am bidding on the construction of a steel frame building and have been asked to price a bi-fold door. The door would be approx 18 feet high x 60 feet wide. I am familiar with your product, I have seen it around airports, as I am a pilot. We built the hanger on Manitoulin Island here in Ontario about 4 years ago. I think it was 60 feet wide by 20 feet high. Could you please send me some pricing so that I may complete my quote to my customer. Please also show installation.

4

I want my ceiling low for heat cost. a 12 ft high door opening would be good. my hanger will be 52 by 52 and I need at least a 48 foot door. The hanger will be steel so what is the lowest side wall I can use. It will have a single slope roof with the door under the angle. 5 feet higher on the left than on the right. also aprox. cost of door and install kit. I will install my self. I will need at least 4 window openings in lower section. Or would a one piece hyd door be better. Thank you Tony

5

We have a new hangar (steel building) with a 12.5' x 40' opening for a one-piece hydraulic door. There are steel I-beams either side of the door opening and stub columns above. We want a flush style door, with an insulated walk door and a battery back-up ssytem, as well as remote control operation. We had a quote from you in August 2008 but were not able to purchase at that time. Now we are getting close and want to see what the current steel prices are (since steel was about at its all time high in August 2008)

6

I am looking for a door approximately 20 ft wide with a clearance of 8 ft. Since this is new construction we can build the steel building accordingly to your specs. I would like the face to be plywood so we can attach the covering we want for appearance.

7

We live in Mankato, MN and we would like to know where the closest door dealer is from us. We are remodeling a steel building and are interested in finding out more about the doors and estimates. Thank you

8

Have a job I'm bidding Door opening 45'x12' that is the clearance needed for the plane metal building has 14' eves. Owner does not want to go higher with the eves. Do you have a door that will work for this clearance. (Note owner is asking about a sliding door ? ) Thanks .Chad

9

I would like a quote on a 40x10 door for anew steel hangar.The best priced door installed.Iam on a private airport and need it as soon as possible.Thanks Jim I will be out of town till Saturday to check on my airplanes repairs.

10

We need to replace sliding doors on our community hangar with a new and better system. The building was built in 1975 and is of all steel I beam construction. We need some general pricing info.

11

Please quote the following material.. 2) 12' x 13' bi-fold doors, one centered in each endwall of a 30 x 50 x 12 3:12 steel building going to Austin, Tx 78705 Thanks- Terry

12

Hello, I need a price for a 40x14 clear span bi-fold door for a steel building. It will need to be shipped to redbluff, ca. Thanks, Richard

13

I am planning on buying the materials to build a 40 x 60 steel building this summer. I would like to know if you have discount sales at any time through out the year. Also, I am curious if you have any thing like "slightly damaged sales" or doors of any size that have been ordered but not purchased. Regardless, I would to price your door plus shipping. Thank you, Murray P.

14

60'x18' door for 65'x65' steel building at new airport in st george ut

15

I need some information and price, if possible, on a bifold lift strap door. - Needs to clear a height of 18' 6" -65' min to 70' max width -What are the thickness of the jambs. The Airplane hanger this will be installed on is 80'. can I put a 70' door in that? -How high do the side walls need to be to accommodate a 18'6" cleared door. - How do you insulate the doors? -What is your lead time to have it to me. - Do you install them? - Who puts on the exterior finish? - This is all on a metal/steal building - Please call me ASAP Thanks Jerry

16

interested on pricing for a bi fold door 50ft wide 25ft high. The Steel Structure has open bay used for sorting onions.

17

Please provide me pricing and data for (2) Bi-Fold or hydraulic door units, sizes will be (1) 70' wide with 18' clear & (1) 50' wide with 18' clear, both will be going at one endwall. spacing will be from left; 5', 70', 10', 50', 5'. Steel Building size will be 140' wide X 80' length X 24' eave height, gable symmetric with 1:12 roof pitch.

18

Please give me a quote on a 60x96x18 steel building with a 40X16.5 bifold in one end, a 14X18 overhead on one side, and a steel walkdoor on the other side. To be built in Wahpeton, ND. Thanks. Rory

19

I self-designed and built a 36x70 steel building. I am looking to install a door in the side-wall of said building. The door frame and header are already installed. At the time of install I planned on using a roll-up door, not realizing the amount of headroom needed. The door frame is constructed of 12 ga material bent into what I call a "Box-C shape"(a sheet of material 18" wide formed at 1" and 4" from each side.) I don't know what any load specs may be on this entire building, let alone the door frame itself.

20

Hello Julie I have put in a couple of request for Schweiss hydraulic doors, and wish to thank you for your co-operation, I do wish pricing of one more size should as my plans may change. Sleepy Hollow I need 15 feet of open height and 60 feet wide. Thanks Brent Banardy

21

please provide quote for bi-fold door to fit into overall opening of 24' high - door to be 50'w x 20'h - eave height of steel buildind is 27'

22

Looking for a quote on a 58 x 17 foot hydraulic door going into a rigid frame steel building with a full framed end wall. We will supply sheeting but need framed openings for 3 3' x 4' windows and 1 3' x 7' walk door delivered to kansas city for march 2010. Please figure installation. Kerry

23

Jeremy, I have received your quote on the door. I thought maybe you had the wrong e-mail address at first --thanks for the good swervice. Gene

24

Do you have an Australian Agent. we are fabricators of cold formed and structural steel structures. We are interested in your products and depending on the range would be interested in becoming your representative. I await your response and further information. Have a nice day. From Terry

25

The building is a Gulf Stream Steal building. Would like turn key price. Options- Lift straps,Manual latches. opening dimensions W-40'6" X h-18'

26

door will be installed in a new steel frame building clear opening size needs to be 40' x 12'

27

Can you please provide the specs for a door that will fit in a 70 x 23 clear opening. THE OVERALL OPENING SIZE FOR THIS DOOR NEEDS TO BE 23' NOT 27'. My eave height for this steel building is 29'.

28

We have your competitors doors now and we're in the process of trying to come up with a modification for the one piece hydraulic door. Sales person on previous quotes was Julie.

29

I am consturcting a prefab shop building manufactured by American Steel. It is 40 feet wide by 43 feet long made of a series of 21 steel arches.

30

Need quote on 20x15 BiFold Door to be installed in a steel-frame structure. Bldg will be insulated. Door to be installed in gable - Bldg height is 18' beneath the truss

31

must have external steel 4x4 with 2 foot header, make quote with and without steel frame

32

We're going to Build a steel framed steel equipment storage building about 50 - feet long * 40 feet wide. floor would be crushed stone. We planned to put 4 doors 12 foot wide * 14 foot high along one long wall (50' -). After seeing your doors we think that we might be better of with 2 of them say 20 feet wide and 14 feet high. Questions Do you sell into Canada ? Do you sell complete doors or assemblies or parts? Please give us a budget estimate of the cost of the doors complete and the cost of the components if you sell them that way also. Deano We're located near Windsor Ontario and directly across the Detroit River from Detroit Michigan

33

Dear Schweiss, I need to know what to tell the building company what loading structures/framing to design into the steel building I am about to purchase. The building I am ordering is a 45 wide X 88 foot deep, with a 2:12 pitch and 16 foot eves. The structure with red metal I beam frame. I was thinking of a 40X12 Hydraulic Door... but if the bi fold door is more economical I would use it instead. Two things, I need some sort of loading requirements to send to the company putting together a building package, and a price quote for the most economical 40X12'opening. if it does not curtail a major cost maybe a 40X14' I would also be insulating the building, thank you for your time and expertise Sincerely Tom

34

I'm still waiting on bldg completion and will have to have the concrete slab completed before we can have exact dimensions for the opening. It is approx. 40'x16'. One concern we have is what might have to be done to strengthen the 40' span on top of opening. This is a 48' wide clear span building with the 40' opening, however the top span is not specifically stressed for hanging any big loads on it so would have to check modifications necessary to accommodate a bi-fold of that size. The side columns are 6" "I" beam 1/4" thick. Do you have any thoughts on this matter??

35

Steal Building 16'H x 20'W

36

Overall SPACE steel bldg size = 60' wide x 60' long x 20' tall. Center bi-fold on endwall. Sincerely, Doug

37

I have a project that need to get a quote on (1)40'x16' and (1)24'x16' one piece hydraulic doors. We will erect the doors. I need loading for the Steel building design.

38

Looking for pricing on 45' x 18' clear bi-fold door for all steel building near Taylorville, IL. At this point in the pricing would like all standard features included. If you could let me know the design information to get with the steel building fabricator. Thank you, Jason

39

Erecting a steel frame building. Need quote on 16X16 doors

40

I have a 40'x30' steel building I would like to put a door in. Here are some of the specs: -The front (30ft. wide) has two regular overhead garage doors. -The side walls are 9ft tall. -All steel building, bolted to all concrete floor. I am wondering if you can put a door in the side (40ft) to fit a Champion Citabria (34ft wide, 7'6" tall). If you could quote both 35' and 36' wide door,and both 8' and 9' high. Let me know what you think. Thanks a lot. Andrew S.

41

I am in the planning stages of building/purchasing a 60ft wide X 100ft long X 12ft eave steel building from my local dealer called KLH. I am interested in a rough price quote on a flush mount hydraulic door and what I would have to do extra to accomidate the additional forces and also some info on what I need to consider on header construction. I plan on having a contractor errect the building but I would install the door and header myself. Thanks, Bob

42

I need a quote on a door. We have installed your bi-folds before and are familiar with them. The building is steel with an opening of 35' 9" x 16'high. The door would be covered in T-111 plywood and is located in the Park City Utah area. The hydraulic door looks like a good choice too.

43

Can you quote me a price on a one piece hydraulic operated door for an opening 39' 8" wide and 10' 6" high. I will need a beam for across the top of this door for the hinge's to attach. What size beam would be required? My building has 4" x 8" verticle steel girders for the end walls. Can you quote me the price with and without the beam for across the top? Thank you, Carl

44

this is a steel bldg 32'w x 20' just built, except for front wall. front wall design is not designed yet

45

I need a quote for a customer who is purchasing one of our steel buildings. I need a quote on a 44x12 door and a 44x13 door. Can you please email me the quotes? Thanks for your help

46

I need offer for large aircraft door W. 14 meters x 3 metes. This door is for new steel buldings we are think to build for one of our cliant.

47

I need a quote on a 16x24 door and I need to know how much space the folded door takes up because I need 15ft6in of clearance. I have not ordered my steel structured building yet so I can change my eve height.

48

I am interested in purchasing a bi-fold or one piece hyd. door for my existing steel building. Please have a salesperson call, so I can explain my needs in more detail. Thank you, Jim E.

49

just starting to maybe build steel building. Looking at maybe 100 x 100 x 20. Half will be used for a shop, wanting a 40' door on shop not sure about the storage side door? Getting prices now to get started. Any prices and advise would be great. We are not in a hurry on building this but if we can pull this off with in our budget maybe get started on building in early or mid summer.Thanks for your time, hope to hear from you soon. BRUCE

50

i have a 40x60 steel framed building i want to install a bi-fold door in one of the 40' openings to accomadate a j-3 cub is tat possible---- any idea of cost thanks tracy

51

We are building a new steel pole building and will need two complete door systems.

52

We are looking at erecting a steel building(90'-320') with the door clear openings being 36'w by 28 and 30'h. I would like some information and pricing if possible. Thanks Rod W.

53

I have an all steel building and was wondering what it would cost for a bifold or a hydraulic door for a 24ft. wide by 14ft. tall opening. I would install it. Thank you, Steve

54

I have a customer who is purchasing one of our steel buildings to be used as a hanger and he needs a 40ft. wide x 12ft tall door. What can you provide to us to resell to him? Cost? Delivery, etc. Thanks,

55

Doors for a Steel Frame building. 2-40'x 16' & 2-24'x 16'

56

I am a Company who build steel constructions. I made a offer for the consctruction of an hangar. The customer asked me to complete this offer with the supply and installations of 11 doors. He show me your offer. I would like to know what this price include (automation latches, door frame, steel carpenty, door panels)the freight charges to Italy (Venice) and if there is a discount. I would like to know also if it's possible to make the steel carpenty ourself to can economize the freight charges. I have to meet the custemer next monday, and so I ask you if it's possible to answer me within tomorrow. Best regards. Riccardo F.

57

We will build a (minimum) steel building of approximately 40' by 80' to house two small aircraft (hanger). We would like you to provide pricing on both bi-fold and one piece hydraulic doors. It appears we will need about a 60' door to accommodate two aircraft.

58

Need information, including pricing, on an aircraft door for an existing steel building. Will be taking out two overhead doors and will need the most efficienct and cost effective aircraft door installed.

59

Clear Height to Doubled (Stacked) 16" X 26 lb beam header attached to 16" X 26 lb colums at 50'-0" c-c spacing. Door will be cased in 6" on both sides (49'-0" door)to provide wall space for down spouts. The building is framed and beginning installation of insulation & sheet metal.

60

Kindly send a quotation for the following: 100 ft x 40 ft Steel Frame building Floor to beam - minimum 15 ft. Wall from bottom up - 5ft Require specification for steel for columns and rafters The plan has to be approved by the Ministry of Planning as a result would require floor plan as follows: 2 side elevation plus back and front. Thanks. Best regards, William G. Managing Director

61

I wish to get a quote for a bi-fold door for an existing building. The building was built by Floyd Construction Co. Berryville, AR. it has steel truses welded up from angle iron, It will require a framework for the door that can be adapted to the building. I am leaning toward a bottom drive with straps.

62

The building is a clear spand. The door opening is approx.

63

I have a U.S. Steel structure, oval in shape I think, that could use a bi-fold door. It's approx. 18-20 foot high and 20 foot wide. Do you have one this size and could you send me some pricing and installation information?

64

Would like some info on one piece hydraulic door for a steel building. Door would be approx. 40 X 16. Would like to have someone to visit for a price quote and and the design of the door. Also to see if the design we want is possible for the building we are putting this on. Brent Call the numbers for cell or shop. Thanks

65

hey i have a steel building and a need two doors i would like to have as many windows as possible and a man door in each one that would be great if you could give me a price

66

I am having a weld up steel shop building erected. Am wanting to install one of your 14x20 hydraulic doors. I am worried that the builder is not making the frame strong enough for the door. He only used 8" I beam for the truss instead of 12" like the others and 11 guage 4" square tube for the door frame which he says is plenty. I am not so sure. I am thinking of insisting on removing the 4" and replacing it with 10 or 12" I beam and adding a reinforcement of 4" square to the inner side of the truss. what would you recommend? If we can make this mess work, I will place the order tomorrow. I have a quote which might not be accurate in these crazy times of prices. I would also like to add some options like the remote control and maybe paint and drill powered emergency pump. Please call me. Thank You Robert

67

CAN YOU PLEASE E-MAIL THE PRELIMINARY SPECS FOR A 50X16 BI-FOLD TO BE INSTALLED ON ONE OF OUR STEEL BUILDINGS. (A-1, THRU A-5) THANKS, KEVIN

68

I am considdering building a new hangar and would like an estimate on a new door. The size is approximate because the hangar is still in consideration. The hangar would be a 75x75x16 all steel construction building.

69

"G'day". Need a quote please for a Bi-fold door on a new steel building ? Building will be 42 X 50 X 14 ....In talking with "many" steel building companies I get different sidewall height requirements for your 12' vertical clearance bi-fold door , so please advise whether I need 16 ' side walls or not? Door to be shipped to Greers Ferry , AR.

70

I'm using 4" square tubing for my side post and 4" x 8" rectangular tubing for header braced to truss.

71

Sir I would like a quote that includes shipping on a 40 ft.X 12 ft. hydraulic door for a new steel building

72

I am interested in a Bi fold door. roughly 25'by 14'for a steel building. Please contact me.

73

Please send a catalouge that I can present in my steel building bids, Thanks, Bryan

74

I have a customer that is interested in an airplane hanger. He needs a door that is 35-40 foot wide. Has a 3 small single engine planes. We sell steel buildings. Looking to setup long term relations with your company. Jason

75

Please compare cost for 2 bi-fold doors vs. 1 large door, I can create the bay openings for the lowest cost alternative. This is not an aircraft hanger. It is a steel building that I want to make secure. For various reasons I do not want a roll-up or tilt-up door. Version A: 2 doors, each 12'x12' Version B: 1 door, 24'x 12' Thanks-

76

I need a quote on 2 bi fold doors 45' wide x 12' tall. They will mount to a new steel building 100' x 48'. We manufacture commercial greenhouses. One of my customers wants us to build him an airplane hanger.

77

Looking for a 40'W by 18'Tall hydraulic one-piece door. Will be installed on a Steel building with a steel support structure.

78

Steel Building size is 60'-0 Wide x 18'-0 Eave, will have main frame endwall with largest door possible. 54'-0 x 14'-0 ? please advise

79

We are building a 60x80x20 all steel heated shop with a 4 foot high concrete wall all the way around with in floor heat. I would like to put a 40 foot door on the east end. Could get by with 35 or 37 foot if available. What is the price difference? Thank You.. Kurt P.S. needs to have remote and windows

80

I would greatly appreciate pricing on 2 sizes of doors. First is a 14ft high by 50 foot wide bi-fold door. Second a 16 ft high by 50 food wide bi-fold door. It is an older building (1988) and I am strongly considering adding on to the end of the building and would put in a bi-fold door. Steel structured building with a concrete base.

81

Can I get a rough bid on a Bi-fold Door for a 90'x25' opening on a steel hangar? Just need to start with and idea if it will be better to go new door or repair existing door.

82

I need a price on a 35x16 door, installed. Location is Argenta, IL. It will be on an 18' tall steel building, on the sidewall. I also need to know weights, for design purposes. Any info would be greatly appreciated. Thanks Jeremy P.

83

Am dealing with a contractor for construction of a site built weld up steel building in late winter.

84

Would like a quote on a 60' X 18' Bifold door erected in a steel building.

85

I'm looking for a 100' x 30' door for an all steel aircraft hanger we are proposing to build here. If you could email me some budget figures for your doors and mail some data, I would appriciate it .

86

We are looking at adding a door to an existing 80' X 180' steel frame building. The size we are looking at is 18' wide X 16' high. Please provide a quoted price installed. Thank you!

87

we have an existing steel building that we would like to put a 40 ft bifold door in.

88

I'd like to explore adding a free standing frame and door to an existing steel hangar. The opening we need is 16 feet high by 60 feet wide. I'm required by city code to provide a Kansas stamped drawing to get the permit for installation. Would that be available?

89

We are putting together a price quote for a steel building to be erected at the Winnemucca Airport.

90

I have customer that is wanting a 40' wide x 20' tall door. Looks to me like the only way to do that is with your "bi-fold". Please forward me information package and pricing for this unit. Do you install? Project is in South Point, Ohio. Installation will be in a new Steel Building. Thanks for your help, ed d. edc

91

I am needing price quotes for a 45' by 14' (clear opening) bi-fold door. Additionally I am looking for turn-key deal, with you guys installing it. I have a steel frame building with rigid endwalls. The door opening on the endwall is not presently framed out, so that work needs to be part of the quote.

92

We are a uk supplier of steel frame buildings, we are at present priceing up a new building which our client is looking to have Bi-Folding doors . The opening size is 15m wide x 6m high and there would be 10 no all with one Personel door . At this stage we only need a guide cost for this doors del U K . Please can you e mail me asap a cost so we can give our client an overhaul budget cost,

93

I am planning on building a steel constructed hanger this fall and am thinking 50X80 with the opening about 50X14. I will currently store my 170 in there but am thinking of resale value if I ever decide to sell the hanger or renting it someone with a small twin. Do I need to consider a bigger opening? Also, can you give an idea what an insulated bi-fold door would cost me. Please keep in mind that we are just at the beginning stages of this project and we are still trying draw up some plans. Thanks, Paul

94

I have listed the larger of the door sizes needed for my current project, but I need to have the complete quote for (2) 16'W x 20'H and the (1) 30'W x 20'H (listed below in click boxes). They will be put into a steel framed structure (i-beams and wide flange col.), but to avoid possible additional structural requirements I'd like to look at the option of a stand alone frame for the doors as well and what bracing may be required. I would also like to know lead time for the listed doors as well to ensure I can stay on schedule. I have check the Catalog request box but would like to request a copy of the catolog via this message just in case that did not register.

95

I need to purchase a 40' X 18' bi-fold door for a client. this door will be included in a steel building purchase. Please send me prices. Thanks, Kathy

96

I am building a new hanger 100long x 120deep with 25" side walls Need door price range to setup financing. I would be looking to start construction within 3 months What is the largest door you can put in the 100 X 25 opening. types and price range please PS Can you recommend a Steel building supplier for this size Hanger.

97

I am constructing a 50 x 60 steel hanger. I am interested in a "one piece door of the deminsion 40 x 14. Please give me a call or forward a quote to my e-mail address. I expet delivery of my building within the next three weeks. Mark R.

98

To whom it may concern, We are planning to build a steel frame hangar(50x50). Could you please send info and pricing for a 45x14(planned opening dimensions) bi-fold, and hydraulic door system. If needed, please provide dimensions for a door that will allow a 45x14 opening when open. Thank you! Brad

99

Building is new construction steel frame and will be insulated.

100

We are put a bid on a steel building going to Okemos, MI. We will need door spec's on these doors. there will be (2) 70Wx18H Doors the . The building is 80w x 160L x 22h with a partition wall down the center will 70' door fit?

101

I AM PUTTING UP A STEEL BUILDING WITH 14'X14' MANUFACTURED OPENING AND WOULD LIKE PRICE OPTIONS ON YOUR DOORS.WOULD LIKE THE OPTION OF WALK-IN DOOR.

102

I would like a quote for two bi-fold doors in a steel building. I am looking at a 25'x12' and a 25'x20'. Please give me a quote to ship to northern california dock. Thanks! Jennifer

103

I previously sent for a quote in mid December, 2006 Please provide as well design loading for steel frame to accomodate the bifold door. Door to be insulated with R 20 and 3'0" X 7'0" Man door. Thanks Lloyd G M. P.Eng. Project Monitor

104

My name is Brian I have a general contracting business in Show Low, AZ. I have a client that needs a quote for a 60%u2019x60%u2019 hangar. As part of that structure, he wants a bi-fold door that is 55' wide & gives 16' of clearance. I need a price & the specs on the requirements for engineering, installation, etc. I need to tell the steel building manufacturer what the overall height that the building will need to be, Thank you for your assistance. Brian S.

105

I plan on building a 50' Steel hanger. I have not picked a supplier. I plan to go with a bi-fold or one piece hydraulic door. The one piece hydraulic door was recommended to me by an owner. I am interested in price comparisons between your bifold and one piece door. I have been asking for a quote on a 50'X14' door for comparisons, but I know the door cannot be the same width as the hanger.

106

The "K" Building is a steel Frame building with wood purlins and girts. our endwall frame will be steel with wood nailers please provide options for remote controls. Thanks Dan E.

107

I'm looking for design loads for one of your Bi-fold doors to fit in the end wall of a 62 ft wide Pre-Engineered Steel Building. We are looking for a 58 ft wide x 16 ft tall Bi-Fold door 1. Weight of door 2. Vert. defection requirments.

108

NEED QUOTATION FOR FOUR HANGAR DOORS. WIDTH 35.27 FT AND HEIGHT 26.25 FT. THE DOORS WILL BE ASSAMBLED ON STELL STUCRURE BUILDING. THE WIND IN THE SITE IS UP TO 35M/S.

109

I am pricing a hangar door for a 60 x 60 x 20 steel building. Door dimensions would be 16' high x 44' wide Thanks Jim H.

110

I have a steel 40x30 airplane hanger at our lake house. I messed up and should have built it 42 or 44 wide as I only have about 18" on each side for the plane to go in. I would like to add a bifold door but am concerned about loosing any more width to the door. Can you help with a solution. I also need to know an approximate price so I can figure if I can afford to do it. I will try to answer your questions as best I can from this location. Your earliest convenience. Thanks Mike J.

111

I have an aircraft maintenance shop with steel structure & steel side panels with a wood roof. The door opening is 10 ft 8 inchs high(clear) by 48 ft 7.5 inches wide(clear).This is the steel support structure dimensions. The floor is concrete. I cannot lose any headroom or width clearance. Can you supply such a door? I am located at the camden county airport (19n) in N.J. John K.